MAX1193ETI+ Maxim Integrated Products, MAX1193ETI+ Datasheet - Page 16

• Manufacturer Part Number: MAX1193ETI+
• Description: IC ADC 8BIT 45MSPS DUAL 28-TQFN
• Manufacturer: Maxim Integrated Products

Specifications of MAX1193ETI+

• Number Of Bits: 8
• Sampling Rate (per Second): 45M
• Data Interface: Parallel
• Number Of Converters: 2
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-WFQFN Exposed Pad
• Conversion Rate: 45 MSPs
• Resolution: 8 bit
• Snr: 48.5 dB
• Voltage Reference: 1.024 V
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Power Dissipation: 1667 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Input Voltage: 3 V
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

provide lowest possible jitter. Any significant aperture
jitter would limit the SNR performance of the on-chip
ADCs as follows:
where f
t
Clock jitter is especially critical for undersampling
applications. The clock input should always be consid-
ered as an analog input and routed away from any ana-
log input or other digital signal lines. The MAX1193
clock input operates with a V
and accepts a 50% ±10% duty cycle (see Typical
Operating Characteristics).
Figure 5 shows the relationship between the clock, ana-
log inputs, A/B indicator, and the resulting output data.
Channel A (CHA) and channel B (CHB) are simultane-
ously sampled on the rising edge of the clock signal
(CLK) and the resulting data is multiplexed at the out-
put. CHA data is updated on the rising edge and CHB
data is updated on the falling edge of the CLK. The A/B
indicator follows CLK with a typical delay time of 6ns
and remains high when CHA data is updated and low
when CHB data is updated. Including the delay
through the output latch, the total clock-cycle latency is
5 clock cycles for CHA and 5.5 clock cycles for CHB.
Ultra-Low-Power, 45Msps, Dual 8-Bit ADC
Figure 5. System Timing Diagram
16
AJ
CHB
is the time of the aperture jitter.
D0–D7
CLK
t
______________________________________________________________________________________
CHA
t
DA/B
A/B
DOB
IN
SNR
represents the analog input frequency and
t
CL
=
CHB
D0B
20
t
System Timing Requirements
CLK
×
t
CH
CHA
D1A
log



2
t
DOA
CHB
D1B
×
DD
π
/2 voltage threshold
×
5 CLOCK-CYCLE LATENCY (CHA), 5.5 CLOCK-CYCLE LATENCY (CHB)
1
CHA
D2A
f
IN
×
t
AJ
CHB
D2B



CHA
D3A
CHB
D3B
D0–D7 and A/B are TTL/CMOS-logic compatible. The
digital output coding is offset binary (Table 2, Figure 6).
The capacitive load on the digital outputs D0–D7
should be kept as low as possible (<15pF) to avoid
large digital currents feeding back into the analog por-
tion of the MAX1193 and degrading its dynamic perfor-
mance. Buffers on the digital outputs isolate them from
Figure 6. Transfer Function
1111 1111
1111 1110
1111 1101
1000 0001
1000 0000
0111 1111
0000 0011
0000 0010
0000 0001
0000 0000
CHA
D4A
-128
CHB
D4B
-127
1LSB =
-126 -125
Channel Data Indicator (A/ B B )
Digital Output Data (D0–D7),
2 x V
V
256
REF
CHA
D5A
REF
INPUT VOLTAGE (LSB)
-1
CHB
D5B
(COM)
0
+1
V
REF
CHA
D6A
V
= V
REF
REFP
+125
- V
+126
REFN
CHB
D6B
+127
+128
(COM)