LTC2439-1IGN Linear Technology, LTC2439-1IGN Datasheet - Page 12
![IC ADC 16BIT 16CH MCRPWR 28SSOP](/photos/6/59/65971/161-28-ssop_sml.jpg)
LTC2439-1IGN
Manufacturer Part Number
LTC2439-1IGN
Description
IC ADC 16BIT 16CH MCRPWR 28SSOP
Manufacturer
Linear Technology
Datasheet
1.LTC2439-1CGN.pdf
(28 pages)
Specifications of LTC2439-1IGN
Number Of Bits
16
Sampling Rate (per Second)
6.8
Data Interface
MICROWIRE™, Serial, SPI™
Number Of Converters
1
Power Dissipation (max)
1mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-SSOP (0.150", 3.95mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC2439-1IGN#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
LTC2439-1
(Bit 18) for the next conversion cycle. Table 3 summarizes
the output data format.
In order to remain compatible with some SPI
microcontrollers, more than 19 SCK clock pulses may be
applied. As long as these clock pulses are complete before
the conversion ends, they will not effect the serial data.
However, switching SCK during a conversion may gener-
ate ground currents in the device leading to extra offset
and noise error sources.
As long as the voltage applied to any channel (CH0-CH15,
COM) is maintained within the – 0.3V to (V
absolute maximum operating range, a conversion result is
generated for any differential input voltage V
–FS = – 0.5 • V
voltages greater than +FS, the conversion result is clamped
to the value corresponding to the +FS + 1LSB. For differ-
ential input voltages below –FS, the conversion result is
clamped to the value corresponding to –FS – 1LSB.
Simultaneous Frequency Rejection
The LTC2439-1 internal oscillator provides better than
87dB normal mode rejection over the range of 49Hz to
61.2Hz as shown in Figure 4. For simultaneous 50Hz/60Hz
rejection using the internal oscillator, F
nected to GND.
When a fundamental rejection frequency different from
the range 49Hz to 61.2Hz is required or when the converter
must be synchronized with an outside source, the
12
Figure 4. LTC2439-1 Normal Mode Rejection
When Using an Internal Oscillator
–100
–100
–120
–130
–140
–80
–90
REF
48
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
to +FS = 0.5 • V
50
U
52
U
54
56
REF
W
58
. For differential input
60
O
24391 F04a
should be con-
62
CC
U
IN
+ 0.3V)
from
LTC2439-1 can operate with an external conversion clock.
The converter automatically detects the presence of an
external clock signal at the F
oscillator. The frequency f
be at least 2560Hz to be detected. The external clock signal
duty cycle is not significant as long as the minimum and
maximum specifications for the high and low periods, t
and t
While operating with an external conversion clock of a
frequency f
normal mode rejection in a frequency range f
±4%. The normal mode rejection as a function of the input
frequency deviation from f
Whenever an external clock is not present at the F
converter automatically activates its internal oscillator and
enters the Internal Conversion Clock mode. The LTC2439-1
operation will not be disturbed if the change of conversion
clock source occurs during the sleep state or during the data
output state while the converter uses an external serial clock.
If the change occurs during the conversion state, the result
of the conversion in progress may be outside specifications
but the following conversions will not be affected. If the
change occurs during the data output state and the con-
verter is in the Internal SCK mode, the serial clock duty cycle
may be affected but the serial data stream will remain valid.
Table 4 summarizes the duration of each state and the
achievable output data rate as a function of F
LEO
Figure 5. LTC2439-1 Normal Mode Rejection When
Using an External Oscillator of Frequency f
, are observed.
–100
–105
–110
–115
–120
–125
–130
–135
–140
EOSC
–80
–85
–90
–95
DEVIATION FROM NOTCH FREQUENCY f
–12
, the LTC2439-1 provides better than 110dB
DIFFERENTIAL INPUT SIGNAL FREQUENCY
–8
–4
EOSC
EOSC
O
pin and turns off the internal
0
/2560 is shown in Figure 5.
of the external signal must
4
EOSC
8
24361 F04b
/2560(%)
EOSC
12
O
EOSC
.
O
pin the
/2560
24391fa
HEO