LTC2415-1CGN Linear Technology, LTC2415-1CGN Datasheet - Page 19

• Manufacturer Part Number: LTC2415-1CGN
• Description: IC ADC 24BIT DIFFINPUT/REF16SSOP
• Manufacturer: Linear Technology

Specifications of LTC2415-1CGN

• Number Of Bits: 24
• Sampling Rate (per Second): 13.75
• Data Interface: MICROWIRE™, Serial, SPI™
• Number Of Converters: 2
• Power Dissipation (max): 1mW
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP (0.150", 3.90mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIO S I FOR ATIO
The serial clock mode is selected on the falling edge of CS.
To select the external serial clock mode, the serial clock pin
(SCK) must be LOW during each CS falling edge.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
While CS is pulled LOW, EOC is output to the SDO pin.
EOC = 1 while a conversion is in progress and EOC = 0 if
the device is in the sleep state. Independent of CS, the
device automatically enters the sleep state once the con-
version is complete. While in the sleep state, if CS is high,
the LTC2415/LTC2415-1 power consumption is reduced
by an order of magnitude
When the device is in the sleep state (EOC = 0), its
conversion result is held in an internal static shift regis-
ter. The device remains in the sleep state until the first
rising edge of SCK is seen while CS is LOW. Data is shifted
out the SDO pin on each falling edge of SCK. This enables
external circuitry to latch the output on the rising edge of
SCK. EOC can be latched on the first rising edge of SCK
and the last bit of the conversion result can be latched on
the 32nd rising edge of SCK. On the 32nd falling edge of
SCK, the device begins a new conversion. SDO goes HIGH
(EOC = 1) indicating a conversion is in progress.
At the conclusion of the data cycle, CS may remain LOW
and EOC monitored as an end-of-conversion interrupt.
(EXTERNAL)
SDO
SCK
CS
Hi-Z
CONVERSION
TEST EOC
U
TEST EOC
U
SLEEP
Hi-Z
Figure 8. External Serial Clock, Single Cycle Operation
W
BIT 31
EOC
BIT 30
ANALOG INPUT RANGE
–0.5V
U
REF
1, 7, 8, 9, 10, 15, 16
0.1V TO V
REFERENCE
TO 0.5V
BIT 29
VOLTAGE
SIG
1 F
2.7V TO 5.5V
REF
CC
BIT 28
MSB
2
3
4
5
6
V
REF
REF
IN
IN
GND
CC
LTC2415-1
+
–
LTC2415/
Alternatively, CS may be driven HIGH setting SDO to Hi-Z.
As described above, CS may be pulled LOW at any time in
order to monitor the conversion status.
Typically, CS remains LOW during the data output state.
However, the data output state may be aborted by pulling
CS HIGH anytime between the first rising edge and the
32nd falling edge of SCK, see Figure 9. On the rising edge
of CS, the device aborts the data output state and imme-
diately initiates a new conversion. This is useful for sys-
tems not requiring all 32 bits of output data, aborting an
invalid conversion cycle or synchronizing the start of a
conversion.
External Serial Clock, 2-Wire I/O
This timing mode utilizes a 2-wire serial I/O interface. The
conversion result is shifted out of the device by an exter-
nally generated serial clock (SCK) signal, see Figure 10. CS
may be permanently tied to ground, simplifying the user
interface or isolation barrier.
The external serial clock mode is selected at the end of the
power-on reset (POR) cycle. The POR cycle is concluded
approximately 0.5ms after V
applied to SCK at this time determines if SCK is internal or
external. SCK must be driven LOW prior to the end of POR
in order to enter the external serial clock timing mode.
+
–
BIT 27
SDO
SCK
DATA OUTPUT
CS
F
O
14
13
12
11
BIT 26
3-WIRE
SPI INTERFACE
V
CC
= 50Hz REJECTION (LTC2415)
= EXTERNAL OSCILLATOR
= 60Hz REJECTION (LTC2415)
= 50Hz/60Hz REJECTION (LTC2415-1)
LTC2415/LTC2415-1
BIT 5
LSB
CC
exceeds 2.2V. The level
SUB LSB
BIT 0
CONVERSION
Hi-Z
TEST EOC
sn2415 24151fs
19
2415 F08