CS5371-BSZR Cirrus Logic Inc, CS5371-BSZR Datasheet - Page 11

• Manufacturer Part Number: CS5371-BSZR
• Description: IC MODULATOR LP/HP 1CH 24-SSOP
• Manufacturer: Cirrus Logic Inc
• Type: Modulatorr

Specifications of CS5371-BSZR

• Sampling Rate (per Second): 512k
• Data Interface: Serial
• Voltage Supply Source: Analog and Digital, Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SSOP
• For Use With: 598-1778 - EVALUATION BOARD FOR CS5376
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Resolution (bits): -

input signal is a steady state DC signal within
±50 mV of the common mode input voltage. Idle
tones result from patterns in the output bitstream
and appear in the measurement spectrum about
-135 dB down from full scale.
Idle tones can be eliminated by adding differential
DC offset to the modulator inputs. The added off-
set should be applied differentially to the inputs,
common mode offsets do not affect idle tones.
5.1.
If the analog inputs are near the common mode
voltage when no signal is present, the OFST pin
can be used to eliminate idle tones.
OFST=1, -50 mV of differential offset is added to
the modulator analog inputs to push the idle tones
out of the measurement bandwidth. Care should
be taken that when OFST is active, offset voltages
generated by external circuitry do not negate the
internally added offset.
5.2.
Offset drift characteristics vary from part to part
and with changes in the power supply voltages. If
the CS5371/72 is used in precision DC measure-
ment applications where offset drift is to be mini-
mized, the power supplies should be well
regulated.
For the lowest offset drift, the CS5371/72 modula-
tors should operate with an MCLK of 2.048 MHz.
The offset drift rate is inversely proportional to
clock frequency, with slower modulator clock rates
exhibiting more offset drift.
MCLK of 1.024 MHz results in twice the offset drift
rate compared to an MCLK of 2.048 MHz.
DS255F3
Offset Enable - OFST
Offset Drift
Operating from an
When
Because offset drift is not linear with temperature,
an exact drift rate per °C cannot be specified. The
CS5371/72 modulators will exhibit approximately
5 ppm/°C of offset drift operating with an MCLK of
2.048 MHz.
6. VOLTAGE REFERENCE INPUTS
The CS5371/72 modulators are designed to oper-
ate with a 2.5 V voltage reference applied across
the VREF+ and VREF- pins to set the full-scale sig-
nal range of the analog inputs. A 2.5 V voltage ref-
erence results in the highest dynamic range and
best signal-to-noise performance, though smaller
reference voltages may be used.
CS5371/72 modulators are operated with a 2.5 V
reference, the analog inputs measure full-scale
signals of 5 volts peak-to-peak fully differential.
In a single supply power configuration the voltage
reference output should be connected to the
VREF+ pin with the VREF- pin connected to
ground. In a dual supply power configuration the
voltage reference should be powered from the VA+
and VA- supplies, with the modulator VREF+ pin
connected to the voltage reference output and the
VREF- pin connected to VA-. Because most 2.5 V
voltage references require a power supply voltage
greater than 3 V to operate, when powering the
voltage reference from dual supplies the reference
voltage into the VREF+ pin should be defined rela-
tive to the VA- supply.
The selected voltage reference should produce
less than 1 µVrms of noise in the measurement
bandwidth on the VREF+ pin. The digital filter out-
put word rate selection determines the bandwidth
CS5371 CS5372
When the
11