MAX1348BETX+T Maxim Integrated Products, MAX1348BETX+T Datasheet - Page 14

• Manufacturer Part Number: MAX1348BETX+T
• Description: IC ADC/DAC 12BIT W/FIFO 36WQFN
• Manufacturer: Maxim Integrated Products
• Type: ADC, DACr

Specifications of MAX1348BETX+T

• Resolution (bits): 12 b
• Sampling Rate (per Second): 225k
• Data Interface: MICROWIRE™, QSPI™, Serial, SPI™
• Voltage Supply Source: Analog and Digital
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 36-WQFN Exposed Pad, 36-HWQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
The MAX1340/MAX1342/MAX1346/MAX1348 integrate
a multichannel 12-bit ADC, and a quad 12-bit DAC in a
single IC. The devices also include a temperature sen-
sor and configurable GPIOs with a 25MHz SPI-/QSPI-
/MICROWIRE-compatible serial interface. The ADC is
available in a 4 or an 8 input-channel version. The four
DAC outputs settle within 2.0µs, and the ADC has a
225ksps conversion rate.
All devices include an internal reference (4.096V) pro-
viding a well-regulated, low-noise reference for both the
ADC and DAC. Programmable reference modes for the
ADC and DAC allow the use of an internal reference, an
external reference, or a combination of both. Features
such as an internal ±1°C accurate temperature sensor,
FIFO, scan modes, programmable internal or external
clock modes, data averaging, and AutoShutdown allow
users to minimize both power consumption and proces-
sor requirements. The low glitch energy (4nV
low digital feedthrough (0.5nV
DACs make these devices ideal for digital control of
fast-response closed-loop systems.
The devices are guaranteed to operate with a supply
voltage from +4.75V to +5.25V. The devices consume
2.5mA at 225ksps throughput, only 22µA at 1ksps
throughput, and under 0.2µA in the shutdown mode.
The MAX1342/MAX1348 offer four GPIOs that can be
configured as inputs or outputs.
Figure 1 shows the MAX1342 functional diagram. The
MAX1342/MAX1348 only include the GPIO A0, A1, GPIO
C0, C1 blocks. The MAX1340/MAX1346 exclude the
GPIOs. The output-conditioning circuitry takes the internal
parallel data bus and converts it to a serial data format at
DOUT, with the appropriate wake-up timing. The arith-
metic logic unit (ALU) performs the averaging function.
The MAX1340/MAX1342/MAX1346/MAX1348 feature a
serial interface that is compatible with SPI and
MICROWIRE devices. For SPI, ensure the SPI bus mas-
ter (typically a microcontroller (µC)) runs in master
mode so that it generates the serial clock signal. Select
the SCLK frequency of 25MHz or less, and set the
clock polarity (CPOL) and phase (CPHA) in the µC con-
trol registers to the same value. The MAX1340/
MAX1342/MAX1346/MAX1348 operate with SCLK idling
high or low, and thus operate with CPOL = CPHA = 0 or
CPOL = CPHA = 1. Set CS low to latch any input data
14
______________________________________________________________________________________
SPI-Compatible Serial Interface
Detailed Description
•
s) of the integrated quad
•
s) and
at DIN on the falling edge of SCLK. Output data at
DOUT is updated on the falling edge of SCLK in clock
modes 00, 01, and 10. Output data at DOUT is updated
on the rising edge of SCLK in clock mode 11. See
Figures 6–11. Bipolar true-differential results and tem-
perature-sensor results are available in two’s comple-
ment format, while all other results are in binary.
A high-to-low transition on CS initiates the data-input
operation. Serial communications to the ADC always
begin with an 8-bit command byte (MSB first) loaded
from DIN. The command byte and the subsequent data
bytes are clocked from DIN into the serial interface on
the falling edge of SCLK. The serial-interface and fast-
interface circuitry is common to the ADC, DAC, and
GPIO sections. The content of the command byte
determines whether the SPI port should expect 8, 16, or
24 bits and whether the data is intended for the ADC,
DAC, or GPIOs (if applicable). See Table 1. Driving CS
high resets the serial interface.
The conversion register controls ADC channel selec-
tion, ADC scan mode, and temperature-measurement
requests. See Table 4 for information on writing to the
conversion register. The setup register controls the
clock mode, reference, and unipolar/bipolar ADC con-
figuration. Use a second byte, following the first, to
write to the unipolar-mode or bipolar-mode registers.
See Table 5 for details of the setup register and see
Tables 6, 7, and 8 for setting the unipolar- and bipolar-
mode registers. Hold CS low between the command
byte and the second and third byte. The ADC averag-
ing register is specific to the ADC. See Table 9 to
address that register. Table 11 shows the details of the
reset register.
Begin a write to the DAC by writing 0001XXXX as a
command byte. The last 4 bits of this command byte
are don’t-care bits. Write another 2 bytes (holding CS
low) to the DAC interface register following the com-
mand byte to select the appropriate DAC and the data
to be written to it. See the DAC Serial Interface section
and Tables 10, 17, and 18.
Write to the GPIOs (if applicable) by issuing a command
byte to the appropriate register. Writing to the
MAX1342/MAX1348 GPIOs requires 1 additional byte fol-
lowing the command byte. See Tables 12–16 for details
on GPIO configuration, writes, and reads. See the GPIO
Command section. Command bytes written to the
GPIOs on devices without GPIOs are ignored.