MCP4132-103E/SN Microchip Technology, MCP4132-103E/SN Datasheet - Page 43
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP4132-103E/SN
Manufacturer Part Number
MCP4132-103E/SN
Description
IC RHEO DGTL SNGL 10K SPI 8SOIC
Manufacturer
Microchip Technology
Datasheet
1.MCP4131-502EP.pdf
(88 pages)
Specifications of MCP4132-103E/SN
Taps
129
Resistance (ohms)
10K
Number Of Circuits
1
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Volatile
Interface
SPI Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Resistance In Ohms
10K
End To End Resistance
10kohm
Track Taper
Linear
No. Of Steps
129
Resistance Tolerance
± 20%
Supply Voltage Range
1.8V To 5.5V
Control Interface
Serial, SPI
No. Of Pots
Single
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP4132-103E/SN
Manufacturer:
Microchip
Quantity:
796
6.1.4
The SPI interface is specified to operate up to 10 MHz.
The actual clock rate depends on the configuration of
the system and the serial command used.
shows the SCK frequency for different configurations.
TABLE 6-1:
© 2008 Microchip Technology Inc.
Volatile
Memory
Memory Type Access
Note 1: MCP41X1 devices only.
2: This is the maximum clock frequency
SERIAL CLOCK (SCK)
(SPI FREQUENCY OF OPERATION)
without an external pull-up resistor.
SDI/SDO
SDI, SDO
SCK FREQUENCY
(1)
250 kHz
10 MHz
Read
Command
(2)
Decrement
Increment,
10 MHz
10 MHz
Write,
Table 6-1
MCP413X/415X/423X/425X
6.1.5
The Chip Select (CS) signal is used to select the device
and frame a command sequence. To start a command,
or sequence of commands, the CS signal must
transition from the inactive state (V
(V
After the CS signal has gone active, the SDO pin is
driven and the clock bit counter is reset.
If an error condition occurs for an SPI command, then
the Command byte’s Command Error (CMDERR) bit
(on the SDO pin) will be driven low (V
error condition, the user must take the CS pin to the V
level.
When the CS pin returns to the inactive state (V
SPI module resets (including the address pointer).
While the CS pin is in the inactive state (V
interface is ignored. This allows the Host Controller to
interface to other SPI devices using the same SDI,
SDO, and SCK signals.
The CS pin has an internal pull-up resistor. The resistor
is disabled when the voltage on the CS pin is at the V
level. This means that when the CS pin is not driven,
the internal pull-up resistor will pull this signal to the V
level.
resistance becomes very large to reduce the device
current consumption.
The high voltage capability of the CS pin allows
MCP413X/415X/423X/425X devices to be used in
systems previously designed for the MCP414X/416X/
424X/426X devices.
IL
Note:
or V
When the CS pin is driven low (V
IHH
).
THE CS SIGNAL
There is a required delay after the CS pin
goes active to the 1st edge of the SCK pin.
IH
) to an active state
DS22060B-page 43
IL
). To exit the
IH
), the serial
IL
IH
), the
) the
IH
IH
IL