MCP4341-502E/ST Microchip Technology, MCP4341-502E/ST Datasheet - Page 41
![IC DGTL POT QUAD 5K 20TSSOP](/photos/29/2/290212/tssop20_sml.jpg)
MCP4341-502E/ST
Manufacturer Part Number
MCP4341-502E/ST
Description
IC DGTL POT QUAD 5K 20TSSOP
Manufacturer
Microchip Technology
Series
WiperLock™r
Datasheet
1.MCP4361-503EML.pdf
(80 pages)
Specifications of MCP4341-502E/ST
Package / Case
20-TSSOP
Taps
129
Resistance (ohms)
5K
Number Of Circuits
4
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
SPI Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Resistance In Ohms
5K
Number Of Pots
Quad
Taps Per Pot
129
Resistance
5 KOhms
Wiper Memory
Non Volatile
Buffered Wiper
Buffered
Digital Interface
SPI
Operating Supply Voltage
2.7 V to 5.5 V
Supply Current
450 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP4341-502E/ST
Manufacturer:
Microchip
Quantity:
329
5.4
Shutdown is used to minimize the device’s current
consumption. The MCP43XX has one method to
achieve this. This is:
•
This is different from the MCP42XXX devices in that the
Hardware Shutdown Pin (SHDN) has been replaced by
a RESET pin. The Hardware Shutdown Pin function is
still available via software commands to the TCON
register.
5.4.1
The Terminal Control (TCON) register is a volatile
register used to configure the connection of each
resistor network terminal pin (A, B, and W) to the
Resistor Network. These registers are shown in
Register 4-2
The RxHW bits forces the selected resistor network
into the same state as the MCP42X1’s SHDN pin.
Alternate low power configurations may be achieved
with the RxA, RxW, and RxB bits.
When the RxHW bit is “0”:
• The P0A, P1A, P2A, and P3A terminals are
• The P0W, P1W, P2W, and P3W terminals are
© 2009 Microchip Technology Inc.
Terminal Control Register (TCON)
disconnected
simultaneously connect to the P0B, P1B, P2B,
and P3B terminals, respectively (see
Note:
Shutdown
TERMINAL CONTROL REGISTER
(TCON)
When the RxHW bit forces the resistor
network into the hardware SHDN state,
the state of the TCON0 or TCON1
register’s RxA, RxW, and RxB bits is
overridden (ignored). When the state of
the RxHW bit no longer forces the resistor
network into the hardware SHDN state,
the TCON0 or TCON1 register’s RxA,
RxW, and RxB bits return to controlling the
terminal connection state. In other words,
the RxHW bit does not corrupt the state of
the RxA, RxW, and RxB bits.
and
Register
4-3.
Figure
5-2)
The RxHW bit does NOT corrupt the values in the
Volatile Wiper Registers nor the TCON register. When
the Shutdown mode is exited (RxHW bit = “1”):
• The device returns to the Wiper setting specified
• The TCON register bits return to controlling the
FIGURE 5-2:
State (RxHW = ‘
by the Volatile Wiper value
terminal connection state
MCP434X/436X
A
B
0
’).
Resistor Network Shutdown
DS22233A-page 41
W