ISL23511WFB8Z-TK Intersil, ISL23511WFB8Z-TK Datasheet
ISL23511WFB8Z-TK
Specifications of ISL23511WFB8Z-TK
Available stocks
Related parts for ISL23511WFB8Z-TK
ISL23511WFB8Z-TK Summary of contents
Page 1
... (GROUND) SS Ordering Information PART NUMBER MARKING ISL23511WFB8Z* (Note 1) 23511 WFBZ ISL23511UFB8Z* (Note 1) 23511 UFBZ ISL23511WFRU10Z* (Note 2) GA ISL23511UFRU10Z* (Note 2) FZ *Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTES: 1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 2
Pinouts ISL23511 (8 LD SOIC) TOP VIEW Pin Descriptions SOIC µTQFN PIN PIN SYMBOL The negative-edge triggered input with internal pull-up. Toggling PU ...
Page 3
... Thermal Resistance (Typical, Note 0.3 8 Lead SOIC . . . . . . . . . . . . . . . . . . . . CC 10 Lead µTQFN . . . . . . . . . . . . . . . . . Maximum Junction Temperature (Plastic Package +150°C CC Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Temperature Range (Extended Industrial .-40°C to +125° Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15mW Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3.0mA TEST CONDITIONS ...
Page 4
Potentiometer Specifications Over recommended operating conditions, unless otherwise specified. (Continued) SYMBOL PARAMETER RDNL Differential Non-linearity (Note 14) Roffset Offset (Note 13) DC Electrical Specifications Over recommended operating conditions unless otherwise specified. SYMBOL PARAMETER I V Active Current ...
Page 5
Slow Mode Timing the AC timing diagram refers to the minimum incremental change in the wiper voltage. Fast Mode Timing the AC timing diagram refers to the minimum ...
Page 6
Typical Performance Curves 160 V = 5.5V CC 140 120 100 80 60 -40º TAP POSITION (DECIMAL) FIGURE 1. WIPER RESISTANCE vs TAP POSITION [ I(RW FOR 10kΩ (W) ...
Page 7
Typical Performance Curves 0 2.7V CC 0.1 0.0 -0 5. TAP POSITION (DECIMAL) FIGURE 7. DNL vs TAP POSITION IN RHEOSTAT MODE FOR 10kΩ (W) 1 5.5V CC ...
Page 8
Power-up and Power-down Requirements There are no restrictions on the power-up or power-down conditions of V and the voltages applied to the CC potentiometer pins provided that V CC positive than or equal to V and The ...
Page 9
... Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: TERMINAL TIP No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. L MILLIMETERS MIN NOMINAL MAX A 0 ...
Page 10
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...