SST39WF1601-70-4C-Y1QE Microchip Technology, SST39WF1601-70-4C-Y1QE Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
SST39WF1601-70-4C-Y1QE
Manufacturer Part Number
SST39WF1601-70-4C-Y1QE
Description
1.65V To 1.95V 16Mbit Multi-Purpose Flash 48 WFBGA 4x6x0.8 Mm TRAY
Manufacturer
Microchip Technology
Series
-r
Specifications of SST39WF1601-70-4C-Y1QE
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
16M (1M x 16)
Speed
70ns
Interface
Parallel
Voltage - Supply
1.65 V ~ 1.95 V
Operating Temperature
0°C ~ 70°C
Package / Case
48-WFBGA
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SST39WF1601-70-4C-Y1QE
Manufacturer:
Microchip Technology
Quantity:
10 000
A Microchip Technology Company
©2011 Silicon Storage Technology, Inc.
Erase-Suspend/Erase-Resume Commands
Chip-Erase Operation
Write Operation Status Detection
for timing waveforms and Figure 24 for the flowchart. Any commands issued during the Sector- or
Block-Erase operation are ignored. When WP# is low, any attempt to Sector- (Block-) Erase the pro-
tected block will be ignored. During the command sequence, WP# should be statically held high or low.
The Erase-Suspend operation temporarily suspends a Sector- or Block-Erase operation thus allowing
data to be read from any memory location, or program data into any sector/block that is not suspended
for an Erase operation. The operation is executed by issuing one byte command sequence with Erase-
Suspend command (B0H). The device automatically enters read mode typically within 20 µs after the
Erase-Suspend command had been issued. Valid data can be read from any sector or block that is not
suspended from an Erase operation. Reading at address location within erase-suspended sectors/
blocks will output DQ
ation is allowed except for the sector or block selected for Erase-Suspend.
To resume Sector-Erase or Block-Erase operation which has been suspended the system must issue
Erase Resume command. The operation is executed by issuing one byte command sequence with
Erase Resume command (30H) at any address in the last Byte sequence.
The SST39WF1601/1602 provide a Chip-Erase operation, which allows the user to erase the entire
memory array to the “1” state. This is useful when the entire device must be quickly erased.
The Chip-Erase operation is initiated by executing a six-byte command sequence with Chip-Erase
command (10H) at address 5555H in the last byte sequence. The Erase operation begins with the ris-
ing edge of the sixth WE# or CE#, whichever occurs first. During the Erase operation, the only valid
read is Toggle Bit or Data# Polling. See Table 6 for the command sequence, Figure 10 for timing dia-
gram, and Figure 24 for the flowchart. Any commands issued during the Chip-Erase operation are
ignored. When WP# is low, any attempt to Chip-Erase will be ignored. During the command sequence,
WP# should be statically held high or low.
The SST39WF1601/1602 provide two software means to detect the completion of a Write (Program or
Erase) cycle, in order to optimize the system write cycle time. The software detection includes two sta-
tus bits: Data# Polling (DQ
the rising edge of WE#, which initiates the internal Program or Erase operation.
The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a
Data# Polling or Toggle Bit read may be simultaneous with the completion of the write cycle. If this
occurs, the system may possibly get an erroneous result, i.e., valid data may appear to conflict with
either DQ
routine should include a loop to read the accessed location an additional two (2) times. If both reads
are valid, then the device has completed the Write cycle, otherwise the rejection is valid.
7
or DQ
6
. In order to prevent spurious rejection, if an erroneous result occurs, the software
2
toggling and DQ
7
) and Toggle Bit (DQ
16 Mbit Multi-Purpose Flash Plus
6
7
at “1”. While in Erase-Suspend mode, a Word-Program oper-
6
SST39WF1601 / SST39WF1602
). The End-of-Write detection mode is enabled after
DS-25014A
Data Sheet
04/11