CAT5221WI-50-T1 ON Semiconductor, CAT5221WI-50-T1 Datasheet
CAT5221WI-50-T1
Specifications of CAT5221WI-50-T1
Related parts for CAT5221WI-50-T1
CAT5221WI-50-T1 Summary of contents
Page 1
CAT5221 Dual Digitally Program- mable Potentiometer (DPPt) with 64 Taps and I Interface Description The CAT5221 is two Digitally Programmable Potentiometers (DPPst) integrated with control logic and 16 bytes of NVRAM memory. Each DPP consists of a series of 63 ...
Page 2
L3B CAT5221WT −RRYMXXXX L = Assembly Location 3 = Lead Finish − Matte−Tin B = Product Revision (Fixed as “B”) CAT = Fixed a “CAT” 5221W = Device Code T = Temperature Range I = Industrial A = Automobile ...
Page 3
Table 1. PIN DESCRIPTION Pin (SOIC) Name 1 R Wiper Terminal for Potentiometer Low Reference Terminal for Potentiometer High Reference Terminal for Potentiometer Device Address, LSB 5 A2 ...
Page 4
Table 2. ABSOLUTE MAXIMUM RATINGS Temperature Under Bias Storage Temperature Voltage on any Pin with Respect with Respect to Ground CC Package Power Dissipation Capability (T Lead Soldering Temperature (10 s) Wiper Current Stresses exceeding Maximum ...
Page 5
Table 5. D.C. OPERATING CHARACTERISTICS Symbol Parameter I Power Supply Current CC I Standby Current ( Input Leakage Current LI I Output Leakage Current LO V Input Low Voltage IL V Input High Voltage ...
Page 6
Table 10. RELIABILITY CHARACTERISTICS Symbol Parameter NEND (Note 9) Endurance TDR (Note 9) Data Retention VZAP (Note 9) ESD Susceptibility ILTH (Notes 9, 10) Latch−Up 9. This parameter is tested initially and after a design or process change that affects ...
Page 7
Serial Bus Protocol The following defines the features of the I 1. Data transfer may be initiated only when the bus is not busy. 2. During a data transfer, the data line must remain stable whenever the clock line is ...
Page 8
Write Operation In the Write mode, the Master device sends the START condition and the slave address information to the Slave device. After the Slave generates an acknowledge, the Master sends the instruction byte that defines the requested operation of ...
Page 9
Instructions and Register Description INSTRUCTIONS Slave Address Byte The first byte sent to the CAT5221 from the master/ processor is called the Slave/DPP Address Byte. The most significant four bits of the slave address are a device type identifier. These ...
Page 10
Wiper Control and Data Registers Wiper Control Register (WCR) The CAT5221 contains two 6−bit Wiper Control Registers, one for each potentiometer. The Wiper Control Register output is decoded to select one of 64 switches along its resistor array. The contents ...
Page 11
The basic sequence of the three byte instructions is illustrated in Figure 11. These three−byte instructions exchange data between the WCR and one of the Data Registers. The WCR controls the position of the wiper. The response of the wiper ...
Page 12
INC/DEC Command Issued SCL SDA R W Figure 13. Increment/Decrement Timing Limits Instruction Format Table 13. READ WIPER CONTROL REGISTER (WCR) S DEVICE ADDRESSES Table 14. WRITE WIPER ...
Page 13
Table 17. GLOBAL TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR) S DEVICE ADDRESSES Table 18. GLOBAL TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR) S DEVICE ADDRESSES ...
Page 14
PIN#1 IDENTIFICATION TOP VIEW D A SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-013. PACKAGE DIMENSIONS SOIC−20, 300 mils CASE 751BJ−01 ISSUE O SYMBOL ...
Page 15
TOP VIEW D A2 SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP20, 4.4x6.5 CASE 948AQ−01 ISSUE θ1 A1 http://onsemi.com 15 SYMBOL MIN ...
Page 16
... The standard lead finish is Matte−Tin. 13. The device used in the above example is a CAT5221WI−10−T1 (SOIC, Industrial Temperature, 10 kW, Tape & Reel, 1,000/Reel). 14. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D ...