X9317US8-2.7 Intersil, X9317US8-2.7 Datasheet
X9317US8-2.7
Specifications of X9317US8-2.7
Related parts for X9317US8-2.7
X9317US8-2.7 Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 XDCP is a trademark of Intersil Americas, Inc. Copyright Intersil Americas Inc. 2004-2005, 2008, 2009. All Rights Reserved All other trademarks mentioned are the property of their respective owners. X9317 FN8183.6 ...
Page 2
... X9317UM8* (Note 2) AEC X9317UM8Z* (Note 1) DCS X9317UM8I* (Note 2) AFE X9317UM8IZ* (Note 1) DCR X9317UP (Note 2) X9317UP X9317UPI (Note 2) X9317UP I X9317US8* (Note 2) X9317U X9317US8Z* (Note 1) X9317U Z X9317US8I* (Note 2) X9317U I X9317US8IZ* (Note 1) X9317U ZI 2 X9317 V LIMITS R TEMPERATURE CC TOTAL (V) (kΩ) RANGE (°C) 5 ±10 + +70 -40 to +85 ...
Page 3
Ordering Information (Continued) PART NUMBER PART MARKING X9317UV8* (Note 2) 9317U X9317UV8Z* (Note 1) 9317U Z X9317UV8I* (Note 2) 317U I X9317UV8IZ* (Note 1) 9317U IZ X9317TM8*, ** (Note 2) AGD X9317TM8Z* (Note 1) DCN X9317TM8I*, ** (Note 2) AGF ...
Page 4
... X9317WV8Z-2.7* (Note 1) 9317W FZ X9317WV8I-2.7*, ** (Note 2) 317W G X9317WV8IZ-2.7* (Note) AKZ X9317UM8-2.7* (Note 2) AED X9317UM8Z-2.7* (Note 1) AOB X9317UM8I-2.7*, ** (Note 2) AFF X9317UM8IZ-2.7* (Note 1) AOH X9317US8-2.7* (Note 2) X9317U F X9317UP-2.7 (Note 2) X9317UP F X9317UPI-2.7 (Note 2) X9317UP G X9317US8Z-2.7* (Note 1) X9317U ZF X9317US8I-2.7*, ** (Note 2) X9317U G X9317US8IZ-2.7* (Note 1) X9317U ZG X9317UV8-2.7* (Note 2) 317U F X9317UV8Z-2 ...
Page 5
Block Diagram V (SUPPLY VOLTAGE) CC UP/DOWN (U/D) CONTROL INCREMENT AND (INC) MEMORY DEVICE SELECT (CS) V (GROUND) SS GENERAL Pin Descriptions PDIP/SOIC/MSOP TSSOP SYMBOL 1 3 INC ...
Page 6
... CS, INC, U/D Input Capacitance IN 6 X9317 Thermal Information Junction Temperature Under Bias . . . . . . . . . . . . . .-65°C to +135°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp V = Full Range Full Operating Temperature Range, unless otherwise stated TEST CONDITIONS/NOTES See “Ordering Information” beginning on ...
Page 7
Endurance and Data Retention PARAMETER Minimum Endurance Data Retention NOTES: 1. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage = [V(R V n(V(R )-V(R ))/99 + V(R W(n)(expected Relative linearity is ...
Page 8
Power-up and Down Requirements The recommended power-up sequence is to apply V first, then the potentiometer voltages. During power-up, the data sheet parameters for the DCP do not fully apply until AC Timing CS t CYC ...
Page 9
Pin Descriptions R AND The high (R ) and low (R ) terminals of the X9317 are H L equivalent to the fixed terminals of a mechanical potentiometer. The terminology relative position of the ...
Page 10
The system may select the X9317, move the wiper and deselect the device without having to store the latest wiper position in nonvolatile memory. After the wiper movement is performed as previously described and once the new position is reached, ...
Page 11
Basic Configurations of Electronic Potentiometers V REF THREE TERMINAL POTENTIOMETER; VARIABLE VOLTAGE DIVIDER Basic Circuits BUFFERED REFERENCE VOLTAGE +5V R LMC7101 REF - OUT W VOLTAGE REGULATOR V 317 IN R ...
Page 12
Mini Small Outline Plastic Packages (MSOP -B- INDEX 1 2 0.20 (0.008) AREA TOP VIEW 0.25 (0.010) GAUGE PLANE SEATING PLANE - 0.10 (0.004) b -H- - 0.20 (0.008) SIDE VIEW 0.20 ...
Page 13
Thin Shrink Small Outline Plastic Packages (TSSOP) N INDEX 0.25(0.010) E AREA E1 - 0.05(0.002) SEATING PLANE - -C- α 0.10(0.004) 0.10(0.004 NOTES: 1. These package ...
Page 14
Package Outline Drawing M8.15E 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 0, 08/09 4 4.90 ± 0.10 PIN NO.1 ID MARK 5 1.27 TOP VIEW 1.75 MAX 0.175 ± 0.075 SIDE VIEW “A (1.27) (5.40) TYPICAL RECOMMENDED LAND ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...