AD5547BRU Analog Devices Inc, AD5547BRU Datasheet - Page 12

• Manufacturer Part Number: AD5547BRU
• Description: IC DAC 16BIT DUAL 38-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5547BRU

• Design Resources: Precision, Unipolar, Inverting Conversion Using AD5547/57 DAC (CN0026) Precision, Unipolar, Noninverting Configuration for the AD5547/57 DAC (CN0027) Precision, Bipolar, Configuration for AD5547/AD5557 DAC (CN0028)
• Settling Time: 500ns
• Number Of Bits: 16
• Data Interface: Parallel
• Number Of Converters: 2
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 55µW
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 38-TSSOP
• Number Of Channels: 2
• Resolution: 16b
• Interface Type: Parallel
• Single Supply Voltage (typ): 5V
• Dual Supply Voltage (typ): Not RequiredV
• Architecture: R-2R
• Power Supply Requirement: Single
• Output Type: Current
• Integral Nonlinearity Error: ±2LSB
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 38
• Package Type: TSSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD5547/AD5557
CIRCUIT OPERATION
DAC SECTION
The AD5547/AD5557 are 16-/14-bit, multiplying, current-
output, parallel input DACs. The devices operate from a single
2.7 V to 5.5 V supply and provide both unipolar (0 V to –V
or 0 V to +V
to +18 V references. In addition to the precision conversion R
commonly found in current output DACs, there are three addi-
tional precision resistors for 4-quadrant bipolar applications.
The AD5547/AD5557 consist of two groups of precision R-2R
ladders, which make up the 12/10 LSBs, respectively. Furthermore,
the 4 MSBs are decoded into 15 segments of resistor value 2R.
Figure 17 shows the architecture of the 16-bit AD5547. Each of
the 16 segments and the R-2R ladder carries an equally weighted
current of one-sixteenth of full scale. The feedback resistor R
and 4-quadrant resistor R
resistor, R1 and R2, equals 5 kΩ. In 4-quadrant operation, R1,
R2, and an external op amp work together to invert the reference
voltage and apply it to the V
connected as shown in Figure 2, the output can swing from
−V
REF
to +V
REF
REF
.
) and bipolar (±V
RCOM
V
OFS
REF
R1
have values of 10 kΩ. Each 4-quadrant
REF
5kΩ
5kΩ
R2
R1
Figure 17. 16-Bit AD5547 Equivalent R-2R DAC Circuit with Digital Section, One Channel Shown
LDAC
input. With R
WR
REF
) output ranges from –18 V
80kΩ
15
2R
LDAC
WR
D15 D14
RA
40kΩ
80kΩ
RB
80kΩ
R
2R
8
OFS
2R
40kΩ
80kΩ
80kΩ
and R
R
R
80kΩ
2R
2R
4
2R
40kΩ
80kΩ
80kΩ
FB
R
R
ADDRESS DECODER
2R
2R
INPUT REGISTER
DAC REGISTER
REF
40kΩ
80kΩ
80kΩ
Rev. B | Page 12 of 20
R
FB
2R
R
2R
FB
80kΩ
40kΩ
80kΩ
R
2R
R
2R
40kΩ
80kΩ
80kΩ
R
2R
2R
The reference voltage inputs exhibit a constant input resistance
of 5 kΩ ± 20%. The impedance of I
dependent. External amplifier choice should take into account
the variation of the AD5547/AD5557 output impedance. The
feedback resistance in parallel with the DAC ladder resistance
dominates output voltage noise. To maintain good analog
performance, it is recommended that the power supply is
bypassed with a 0.01 μF to 0.1 μF ceramic or chip capacitor in
parallel with a 1 μF tantalum capacitor. Also, to minimize gain
error, PCB metal traces between V
Every code change of the DAC corresponds to a step function;
gain peaking at each output step may occur if the op amp has
limited GBP and excessive parasitic capacitance present at the
inverting node of the op amp. A compensation capacitor, therefore,
may be needed between the I-to-V op amp inverting and output
nodes to smooth the step transition. Such a compensation capacitor
should be found empirically, but a 20 pF capacitor is generally
adequate for the compensation.
The V
the DAC switches. Note that the output precision degrades if
the operating voltage falls below the specified voltage. Users
should also avoid using switching regulators because device
power supply rejection degrades at higher frequencies.
80kΩ
40kΩ
R
2R
DD
4-BIT R2R
40kΩ
80kΩ
D0
power is used primarily by the internal logic to drive
R
2R
RS
RS
80kΩ
2R
80kΩ
2R
RS
10kΩ
4 MSB
15 SEGMENTS
8-BIT R2R
10kΩ
ROFS
RFB
IOUT
AGND
REF
OUT
and R
, the DAC output, is code
FB
should match.