LQ10D36A Sharp Electronics, LQ10D36A Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LQ10D36A
Manufacturer Part Number
LQ10D36A
Description
Manufacturer
Sharp Electronics
Datasheet
1.LQ10D36A.pdf
(21 pages)
Specifications of LQ10D36A
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LQ10D36A
Manufacturer:
Sharp Microelectronics
Quantity:
135
10. Display Quality
11.Handling Precautions
o) Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
h) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.
i) Protection film is attached to the module surface to prevent it from being scratched .
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel
l) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.
m) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to
n) When handling LCD modules and assembling them into cabinets, please be noted that long-term
p) Be careful of a back light lead not to pull by force at the time of the wiring to an inverter, or line processing.
q) When install LCD modules in the cabinet, recommended torque value is “0.294±0.02N・m
r) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets
s) Notice:Never dismantle the module , because it will cause failure.
t) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
u) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
v) If a minute particle enters in the module and adheres to an optical material, it may cause display non-
w) The lamp used for this product is very sensitive to the temperature. Luminance decreases rapidly when it is
The display quality of the color TFT-LCD module shall be in compliance with the
Incoming Inspection Standard.
ordinances or regulations for disposal.
is used under such environment. If a light strong against a LCD panel is irradiated, it may lead to
degradation of the panel characteristic and display grace may get worse.
when handling. Observe all other precautionary requirements in handling electric components.
Peel the film off slowly, just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
protective board over the LCD, be careful about the optical interface fringe etc. which degrades
display quality.
electrical shock. When exchange lamps or service, turn off the power without tail.
storage in the environment of oxidization or deoxidization gas, and the use of such materials as reagent,
solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion, discoloration,
degradation of display grace, and abnormalities of operation.
(3.0±0.2kgf・cm)”.
Be sure to confirm it in the same condition as it is installed in your instrument.
inside your eye or mouth by mistake.
If adjusted value is changed, the specification may not be satisfied.
warp or twist.
Handle with care.
Please make it like. If stress is added, there is a possibility that circuit parts may be damaged.
uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you
intend to install a fan.
used for a long time or repeatedly under the environment of the low temperature or the module is being
cooled. Please avoid the continuous or repeatedly use of it such an environment.
It may decrease up to 50% of the initial luminance in about one month under the low temperature
environment. Please consult our company when it is used under the environment like above mentioned.
Data Modul AG - www.data-modul.com
17