LQ104V1DC31 Sharp Electronics, LQ104V1DC31 Datasheet
LQ104V1DC31
Specifications of LQ104V1DC31
Available stocks
Related parts for LQ104V1DC31
LQ104V1DC31 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ104V1DC31 TFT-LCD Module Spec. Issue Date: December 13, 2005 AVC Liquid Crystal Displays Group No: LD-12604B ...
Page 2
...
Page 3
... Application This specification applies to color TFT-LCD module, LQ104V1DC31 (This specification is only applied for the module which has letter "A" at the end of the lot number of the module.) These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 4
Mechanical Specifications Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1.Note: excluding backlight cables. Outline dimensions is shown in Fig.1 Specifications 26 (10.4") Diagonal 211.2(H) 158.4(V) 640(H) ...
Page 5
Input Terminals 4-1. TFT-LCD panel driving 1 2 CN1 pin arrangement from module surface Pin No. Symbol 1 GND 2 CK Clock signal for sampling each data signal 3 Hsync Horizontal synchronous signal 4 Vsync Vertical synchronous signal 5 ...
Page 6
Note3 Note4 I Absolute Maximum Ratings Parameter Input voltage +5V supply voltage Storage temperature Operating temperature Operating temperature Light source wave length Light source luminance Note1 CK,R0 R5,G0 G5,B0 B5,Hsync,Vsync,ENAB, R/L, U/L Note2 Humidity 95%RH Max. ...
Page 7
Electrical Characteristics 6-1.TFT-LCDpaneldriving Ta 25 Parameter Power Supply voltage Supply Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (low) Input current (High) NOTE 1 Vcc-turn-on conditions Vcc-dip conditions Vcc-dip condition should also follow ...
Page 8
Timing Characteristics of input signals Timing diagrams of input signal are shown in Fig.2 - 7-1. Timing characteristics Parameter Symbol Mode Clock Frequency 1/Tc High time Tch Low time Tcl Data Setup time Tds Hold time Tdh Horizontal Cycle ...
Page 9
Vertical display position The vertical display position is automatically centered in the active area at each mode of VGA ,480-,400-,and 350-line mode . Each mode is selected depending on the polarity of the synchronous signals described in 4-1(Note1). In ...
Page 10
...
Page 11
...
Page 12
...
Page 13
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale R0 R1 Gray Scale Black 0 0 Blue 0 0 Green 0 0 Cyan 0 0 Red 1 1 Magenta 1 1 Yellow 1 ...
Page 14
Optical Characteristics (It is usually required to measure under the following condition.condition:IL=6.0mA,Ta=25 Parameter Symbol Viewing Horizontal Angle Vertical Range Contrast ratio Response Rise Time Decay Chromaticity of White Transmissivity [Use the backlight of LQ10D421 for measurement] The measurement shall ...
Page 15
Note1 Definitions of viewing angle range ’clo ck d irectio n Note2 Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) Note3 Definition of response time: The response time is defined as ...
Page 16
Display Quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. 11 Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable ...
Page 17
... Pulse width : 11ms, half sine wave Direction : once for each direction. Packing box Model.No Shipment Date LQ104V1DC31 社内品番 ： ＬｏｔＮＯ． ： Ｑｕａｎｔｉｔｙ： ユーザ品番 ： ...
Page 18
...
Page 19
...
Page 20
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...