LQ104V1DC31 Sharp Electronics, LQ104V1DC31 Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LQ104V1DC31
Manufacturer Part Number
LQ104V1DC31
Description
Manufacturer
Sharp Electronics
Datasheet
1.LQ104V1DC31.pdf
(20 pages)
Specifications of LQ104V1DC31
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LQ104V1DC31
Manufacturer:
SHARP
Quantity:
1 000
10. Display Quality
11 Handling Precautions
.
12.Packing form
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
c) Since the polarizer is easily damaged, pay attention not to scratch it.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
j)Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is
k)When you use the module , please apply enough EMI countermeasure by using optimum backlight
l) When handling LCD modules and assembling them into cabinets, please be noted that long-term
m) When handling LCD modules and assembling them into cabinets, please be noted that long-term
n) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD
o) When install LCD modules in the cabinet, recommended torque value is “0.294 0.02N m
p) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets
q) Notice:Never dismantle the module , because it will cause failure.
r) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
s) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
h) Protection film is attached to the module surface to prevent it from being scratched .
t) If a minute particle enters in the module and adheres to an optical material, it may cause display non-
Incoming Inspection Standard.
i) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
The display quality of the color TFT-LCD module shall be in compliance with the
used under such environment.
sysutem etc..
warp or twist.
Handle with care.
Peel the film off slowly , just before the use, with strict attention to electrostatic charges. Ionized
air shall be blown over during the action. Blow off 'dust' on the polarizer by using an ionized nitrogen.
protective board over the LCD, be careful about the optical interface fringe etc. which degrades
display quality.
storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent,
solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the
LCD modules.
storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent,
solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the
LCD modules.
panel is used under such environment.
(3.0 0.2kgf cm)”.
Be sure to confirm it in the same condition as it is installed in your instrument.
inside your eye or mouth by mistake.
If adjusted value is changed, the specification may not be satisfied.
uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you
intend to install a fan.
Piling number of cartons
Packing quantity in one carton
Carton size [mm]
Total mass of one carton filled with full modules
Packing form is shown
when handling.Observe all other precautionary requirement in handling electric components.
525 (W)×309(D)×377(H)
Fig.4
20
10kg
Max