72265LA10PF Integrated Device Technology (Idt), 72265LA10PF Datasheet - Page 8

• Manufacturer Part Number: 72265LA10PF
• Description: FIFO Mem Sync Dual Depth/Width Uni-Dir 16K x 18 64-Pin TQFP
• Manufacturer: Integrated Device Technology (Idt)

Specifications of 72265LA10PF

• Package: 64TQFP
• Configuration: Dual
• Bus Directional: Uni-Directional
• Density: 288 Kb
• Organization: 16Kx18
• Data Bus Width: 18 Bit
• Timing Type: Synchronous
• Expansion Type: Depth|Width
• Typical Operating Supply Voltage: 5 V
• Operating Temperature: 0 to 70 °C

PROGRAMMING FLAG OFFSETS
IDT72255LA/72265LA has internal registers for these offsets. Default set-
tings are stated in the footnotes of Table 1 and Table 2. Offset values can be
programmed into the FIFO in one of two ways; serial or parallel loading
method. The selection of the loading method is done using the LD (Load)
pin. During Master Reset, the state of the LD input determines whether
serial or parallel flag offset programming is enabled. A HIGH on LD during
Master Reset selects serial loading of offset values and in addition, sets a
default PAE offset value of 3FFH (a threshold 1,023 words from the empty
boundary), and a default PAF offset value of 3FFH (a threshold 1,023
words from the full boundary). A LOW on LD during Master Reset selects
parallel loading of offset values, and in addition, sets a default PAE offset
TABLE 1 — STATUS FLAGS FOR IDT STANDARD MODE
IDT72255LA/72265LA CMOS SuperSync FIFO™
8,192 x 18 and 16,384 x 18
NOTES:
1. n = Empty Offset, Default Values: n = 127 when parallel offset loading is selected or n = 1,023 when serial offset loading is selected.
2. m = Full Offset, Default Values: m = 127 when parallel offset loading is selected or m = 1,023 when serial offset loading is selected.
TABLE 2 — STATUS FLAGS FOR FWFT MODE
NOTES:
1. n = Empty Offset, Default Values: n = 127 when parallel offset loading is selected or n = 1,023 when serial offset loading is selected.
2. m = Full Offset, Default Values: m = 127 when parallel offset loading is selected or m = 1,023 when serial offset loading is selected.
Full and Empty Flag offset values are user programmable. The
Words in
FIFO
Words in
FIFO
Number of
Number of
(1)
4,098 to (8,193–(m+1))
4,097 to (8,192–(m+1))
(8,192–m)
(8,193–m) to 8,192
(n + 1) to 4,096
(n + 2) to 4,097
IDT72255LA
IDT72255LA
1 to n+1
1 to n
8,192
8,193
0
0
(2)
(1)
to 8,191
(1)
(2)
8
value of 07FH (a threshold 127 words from the empty boundary), and a
default PAF offset value of 07FH (a threshold 127 words from the full
boundary). See Figure 3, Offset Register Location and Default Values.
the current offset values. It is only possible to read offset values via parallel
read.
rizes the control pins and sequence for both serial and parallel program-
ming modes. For a more detailed description, see discussion that follows.
after Master Reset, regardless of whether serial or parallel programming
has been selected.
In addition to loading offset values into the FIFO, it also possible to read
Figure 4, Programmable Flag Offset Programming Sequence, summa-
The offset registers may be programmed (and reprogrammed) any time
8,194 to (16,385–(m+1))
8,193 to (16,384–(m+1))
(16,384–m)
(16,385–m)
(n + 1) to 8,192
(n + 2) to 8,193
IDT72265LA
IDT72265LA
1 to n+1
1 to n
16,384
16,385
0
0
(2)
(2)
(1)
to 16,383
to 16,384
(1)
(2)
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
FF PAF
FF PAF
H
H
H
H
H
H
L
L
L
L
L
L
JANUARY 13, 2009
H
H
H
H
H
H
H
H
L
L
L
L
HF
HF
H
H
H
H
H
H
L
L
L
L
L
L
PAE EF
PAE EF
H
H
H
H
H
H
H
H
L
L
L
L
H
H
H
H
H
H
L
L
L
L
L
L