GA355QR7GB103KW01L Murata Electronics, GA355QR7GB103KW01L Datasheet - Page 198

• Manufacturer Part Number: GA355QR7GB103KW01L
• Manufacturer: Murata Electronics

!Note
180
16
18
*1 "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
*2 "C" expresses nominal capacitance value (pF).
GA3 Series Specifi cations and Test Methods
Continued from the preceding page.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
Q
Q
Q
No marking defects
More than 3,000MΩ
In accordance with item No.4
No marking defects
More than 3,000MΩ
In accordance with item No.4
No marking defects
More than 3,000MΩ
In accordance with item No.4
X7R
X7R
X7R
X7R
X7R
X7R
SL
SL
SL
SL
SL
SL
Within ±2.5% or ±0.25pF
(Whichever is larger)
Within ±5.0% or ±0.5pF
(Whichever is larger)
Within ±3.0% or ±0.3pF
(Whichever is larger)
QU400+20C*
QU1000
QU275+5/2C*
QU350
QU275+5/2C*
QU350
Within ±15%
Within ±15%
Within ±20%
D.F.V0.05
D.F.V0.05
D.F.V0.05
2
2
2
(CU30pF)
(CF30pF)
(CF30pF)
(CU30pF)
(CF30pF)
(CU30pF)
Fix the capacitor to the supporting jig (glass epoxy board) shown
in Fig. 4.
Perform the 5 cycles according to the 4 heat treatments listed in
the following table.
Let sit for 24±2 hrs. at room condition,*
Before this test, the test shown in the following is performed.
·Item 11 Adhesive Strength of Termination (applied force is 5N)
·Item 13 Deflection
Let the capacitor sit at 40±2°C and relative humidity of 90 to 95%
for 500
Remove and let sit for 24±2 hrs. at room condition,*
measure.
Before this test, the test shown in the following is performed.
·Item 11 Adhesive Strength of Termination (apply force is 5N)
·Item 13 Deflection
Impulse Voltage
Each individual capacitor should
be subjected to a 2.5kV (Type
GC/GF: 5kV) Impulse (the
voltage value means zero to
peak) for three times. Then the
capacitors are applied to life test.
Apply voltage as in Table for 1,000 hrs. at 125
humidity 50% max.
Let sit for 24±2 hrs. at room condition,*
Perform a heat treatment at 150
let sit for 24±2 hrs. at room condition.*
Perform a heat treatment at 150
let sit for 24±2 hrs. at room condition.*
Perform a heat treatment at 150
let sit for 24±2 hrs. at room condition.*
GC
GD
GB
W24
Y
1
2
3
4
AC312.5V (r.m.s.), except that once each hour the
voltage is increased to AC1,000V (r.m.s.) for 0.1 sec.
AC425V (r.m.s.), except that once each hour the
voltage is increased to AC1,000V (r.m.s.) for 0.1 sec.
0
hrs.
Max. Operating Temp.±2
Min. Operating Temp.±3
Glass Epoxy Board
Room Temp.
Room Temp.
Fig. 4
Continued on the following page.
W
Y10
W
Y10
W
Y10
0
0
0
100
°C for 60±5 min. and then
°C for 60±5 min. and then
0
°C for 60±5 min. and then
Front time (T
Time to half-value (T
90
50
30
Solder resist
Cu
1
1
1
1
1
(%)
then measure.
then measure.
T
T
1
T
2
W2
Y0
1
)=1.2μs=1.67T
2 to 3
2 to 3
30±3
30±3
°C, relative
1
then
2
)=50μs
t
C02E.pdf
Oct.1,2012