AD9777BSV Analog Devices Inc, AD9777BSV Datasheet - Page 46
![IC DAC 16BIT DUAL 160MSPS 80TQFP](/photos/6/64/66419/505-80-tqfp_sml.jpg)
AD9777BSV
Manufacturer Part Number
AD9777BSV
Description
IC DAC 16BIT DUAL 160MSPS 80TQFP
Manufacturer
Analog Devices Inc
Series
TxDAC+®r
Datasheet
1.AD9777BSVZ.pdf
(60 pages)
Specifications of AD9777BSV
Rohs Status
RoHS non-compliant
Settling Time
11ns
Number Of Bits
16
Data Interface
Parallel
Number Of Converters
2
Voltage Supply Source
Analog and Digital
Power Dissipation (max)
410mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
80-TQFP Exposed Pad, 80-eTQFP, 80-HTQFP, 80-VQFP
For Use With
AD9777-EBZ - BOARD EVALUATION FOR AD9777
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9777BSV
Manufacturer:
AD
Quantity:
1 831
Part Number:
AD9777BSV
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9777BSV#
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9777BSVZ
Manufacturer:
AD
Quantity:
1 000
Company:
Part Number:
AD9777BSVZ
Manufacturer:
ADI
Quantity:
182
Company:
Part Number:
AD9777BSVZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9777BSVZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9777BSVZRL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
AD9777
APPLYING THE OUTPUT CONFIGURATIONS
The following sections illustrate typical output configurations
for the AD9777. Unless otherwise noted, it is assumed that
I
optimum dynamic performance, a differential output configu-
ration is suggested. A simple differential output may be
achieved by converting I
terminating them to AGND via equal value resistors. This type
of configuration may be useful when driving a differential
voltage input device such as a modulator. If a conversion to a
single-ended signal is desired and the application allows for ac
coupling, an RF transformer may be useful; if power gain is
required, an op amp may be used. The transformer configura-
tion provides optimum high frequency noise and distortion
performance. The differential op amp configuration is suitable
for applications requiring dc coupling, signal gain, and/or level
shifting within the bandwidth of the chosen op amp.
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage
results if I
referred to AGND. This configuration is most suitable for a
single-supply system requiring a dc-coupled, ground referred
output voltage. Alternatively, an amplifier could be configured
as an I-V converter, thus converting I
negative unipolar voltage. This configuration provides the best
DAC dc linearity as I
virtual ground.
UNBUFFERED DIFFERENTIAL OUTPUT,
EQUIVALENT CIRCUIT
In many applications, it may be necessary to understand the
equivalent DAC output circuit. This is especially useful when
designing output filters or when driving inputs with finite input
impedances. Figure 97 illustrates the output of the AD9777 and
the equivalent circuit. A typical application where this
information may be useful is when designing an interface filter
between the AD9777 and the Analog Devices AD8345
quadrature modulator.
OUTFS
is set to a nominal 20 mA. For applications requiring
I
OUTFS
OUTA
× (R
and/or I
V
Figure 97. DAC Output Equivalent Circuit
SOURCE
A
+ R
p-p
OUTA
B
=
)
OUTB
I
I
OUTA
OUTA
OUTB
or I
is connected to a load resistor, R
R
A
and I
OUTB
+ R
B
are maintained at ground or
OUTB
V
(DIFFERENTIAL)
OUTA
OUT
to a voltage output by
V
V
OUT
OUT
or I
+
–
OUTB
into a
LOAD
Rev. C | Page 46 of 60
,
For the typical situation, where I
both equal 50 Ω, the equivalent circuit values become
Note that the output impedance of the AD9777 DAC itself is
greater than 100 kΩ and typically has no effect on the
impedance of the equivalent output circuit.
DIFFERENTIAL COUPLING USING A
TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion, as shown in Figure 98. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral
content lies within the transformer’s pass band. An RF
transformer, such as the Mini-Circuits T1-1T, provides excellent
rejection of common-mode distortion (that is, even-order
harmonics) and noise over a wide frequency range. It also
provides electrical isolation and the ability to deliver twice the
power to the load. Transformers with different impedance ratios
may also be used for impedance matching purposes.
The center tap on the primary side of the transformer must be
connected to AGND to provide the necessary dc current path
for both I
at I
around AGND and should be maintained within the specified
output compliance range of the AD9777. A differential resistor,
R
transformer is connected to the load, R
reconstruction filter or cable. R
transformer’s impedance ratio and provides the proper source
termination that results in a low VSWR. Note that approxi-
mately half the signal power dissipates across R
DIFF
OUTA
V
R
, can be inserted in applications where the output of the
OUT
SOURCE
and I
OUTA
= 100 Ω
= 2 V
Figure 98. Transformer-Coupled Output Circuit
OUTB
and I
I
DAC
I
OUTA
OUTB
(that is, V
P-P
OUTB
. The complementary voltages appearing
MINI-CIRCUITS
OUTA
T1-1T
DIFF
and V
OUTFS
is determined by the
= 20 mA and R
OUTB
LOAD
R
) swing symmetrically
LOAD
, via a passive
DIFF
.
A
and R
B