ADSP-2173BST-80 Analog Devices Inc, ADSP-2173BST-80 Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADSP-2173BST-80
Manufacturer Part Number
ADSP-2173BST-80
Description
IC DSP CONTROLLER 16BIT 128TQFP
Manufacturer
Analog Devices Inc
Series
ADSP-21xxr
Type
Fixed Pointr
Datasheet
1.ADSP-2171BSZ-133.pdf
(52 pages)
Specifications of ADSP-2173BST-80
Rohs Status
RoHS non-compliant
Interface
Host Interface, Serial Port
Clock Rate
20MHz
Non-volatile Memory
External
On-chip Ram
10kB
Voltage - I/o
3.30V
Voltage - Core
3.30V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
128-TQFP, 128-VQFP
Device Core Size
16b
Architecture
Enhanced Harvard
Format
Fixed Point
Clock Freq (max)
20MHz
Mips
20
Device Input Clock Speed
20MHz
Ram Size
10KB
Program Memory Size
24KB
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
128
Package Type
TQFP
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADSP-2173BST-80
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADSP-2171/ADSP-2172/ADSP-2173
ADSP-2171/ADSP-2172
CAPACITIVE LOADING
Figures 19 and 20 show the capacitive loading characteristics of
the ADSP-2171/ADSP-2172.
Figure 19. Typical Output Rise Time vs. Load Capacitance,
C
Figure 20. Typical Output Valid Delay or Hold vs. Load
Capacitance, C
Temperature)
TEST CONDITIONS
Output Disable Time
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured out-
put high or low voltage to a high impedance state. The output
disable time (t
shown in the Output Enable/Disable diagram. The time is the
interval from when a reference signal reaches a high or low volt-
age level to when the output voltages have changed by 0.5 V
from the measured output high or low voltage. The decay time,
L
(at Maximum Ambient Operating Temperature)
NOMINAL
28
24
20
16
12
8
4
+14
+12
+10
+8
+4
+2
–2
DIS
L
) is the difference of t
25
(at Maximum Ambient Operating
25
50
50
V
DD
75
C
= 4.5V
L
75
– pF
C
L
100
– pF
MEASURED
100
125
125
and t
150
150
DECAY
, as
–30–
t
rent load, i
following equation:
from which
is calculated. If multiple pins (such as the data bus) are dis-
abled, the measurement value is that of the last pin to stop
driving.
Output Enable Time
Output pins are considered to be enabled when that have made
a transition from a high-impedance state to when they start driv-
ing. The output enable time (t
reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in the Output Enable/Disable diagram. If multiple pins (such as
the data bus) are enabled, the measurement value is that of the
first pin to start driving.
DECAY
REFERENCE
Figure 21. Voltage Reference Levels for AC Measure-
ments (Except Output Enable/Disable)
Figure 23. Equivalent Device Loading for AC Measure-
ments (Including All Fixtures)
OUTPUT
(MEASURED)
(MEASURED)
SIGNAL
, is dependent on the capacitative load, C
OUTPUT
V
INPUT
V
OUTPUT
L
OL
OH
, on the output pin. It can be approximated by the
Figure 22. Output Enable/Disable
PIN
TO
t
MEASURED
OUTPUT STOPS
t
DIS
DRIVING
t
DIS
50pF
t
DECAY
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
V
V
OH
OL
t
t
MEASURED
DECAY
(MEASURED) +0.5V
(MEASURED) – 0.5V
ENA
C
L
) is the interval from when a
• 0.5V
I
I
OH
OL
i
– t
L
DECAY
0.3V
0.0V
1.5V
1.5V
2.0V
OUTPUT STARTS
3.0V
1.0V
2.0V
DRIVING
L
t
ENA
, and the cur-
+1.5V
V
(MEASURED)
V
(MEASURED)
OH
OL
REV. A