ADSP-2184NBST-320 Analog Devices Inc, ADSP-2184NBST-320 Datasheet - Page 24

• Manufacturer Part Number: ADSP-2184NBST-320
• Description: IC DSP CONTROLLER 16BIT 100LQFP
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2184NBST-320

• Rohs Status: RoHS non-compliant
• Interface: Host Interface, Serial Port
• Clock Rate: 80MHz
• Non-volatile Memory: External
• On-chip Ram: 20kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.90V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• Device Core Size: 16b
• Architecture: Enhanced Harvard
• Format: Fixed Point
• Clock Freq (max): 80MHz
• Mips: 80
• Device Input Clock Speed: 80MHz
• Ram Size: 20KB
• Program Memory Size: Not RequiredKB
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (max): 2/3.6V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / Rohs Status: Not Compliant

ADSP-218xN
ESD DIODE PROTECTION
During the power-up sequence of the DSP, differences in the
ramp-up rates and activation time between the two supplies can
cause current to flow in the I/O ESD protection circuitry. To
prevent damage to the ESD diode protection circuitry, Analog
Devices recommends including a bootstrap Schottky diode.
The bootstrap Schottky diode is connected between the core
and I/O power supplies, as shown in
ADSP-218xN processor from partially powering the I/O supply.
Including a Schottky diode will shorten the delay between the
supply ramps and thus prevent damage to the ESD diode pro-
tection circuitry. With this technique, if the core rail rises ahead
of the I/O rail, the Schottky diode pulls the I/O rail along with
the core rail.
Table 13. Example Power Dissipation Calculation
1
Parameters
Address
Data Output, WR
RD
CLKOUT, DMS
Total power dissipation for this example is P
DC INPUT
SOURCE
Figure 17. Dual Voltage Schottky Diode
REGULATOR
REGULATOR
I/O VOLTAGE
VOLTAGE
CORE
No. of Pins
7
9
1
2
INT
Figure
+ 45.72 mW.
V
V
DDEXT
DDINT
17. It protects the
ADSP-218xN
Rev. A | Page 24 of 48 | August 2006
1
× C (pF)
10
10
10
10
× V
3.3
3.3
3.3
3.3
POWER DISSIPATION
To determine total power dissipation in a specific application,
the following equation should be applied for each output: C
V
where:
C = load capacitance.
f = output switching frequency.
Example: In an application where external data memory is used
and no other outputs are active, power dissipation is calculated
as follows:
Assumptions:
Total Power Dissipation = P
P
(C
ple in
2
2
2
2
DDEXT
DD
INT
• External data memory is accessed every cycle with 50% of
• External data memory writes occur every other cycle with
• Each address and data pin has a 10 pF total load at the pin.
• Application operates at V
2
the address pins switching.
50% of the data pins switching.
= internal power dissipation from
V
2
Table
DDEXT
(V)
f
2
13.
f) is calculated for each output, as in the exam-
× f (MHz)
20.0
20.0
20.0
40.0
INT
DDEXT
+ (C
= 3.3 V and t
V
Figure 22 on Page
DDEXT
2
PD (mW)
15.25
19.59
45.72
2.18
8.70
f)
CK
= 30 ns.
27.