EP1S30F780C7 Altera, EP1S30F780C7 Datasheet - Page 187
![IC STRATIX FPGA 30K LE 780-FBGA](/photos/6/72/67270/544-780-fbga_sml.jpg)
EP1S30F780C7
Manufacturer Part Number
EP1S30F780C7
Description
IC STRATIX FPGA 30K LE 780-FBGA
Manufacturer
Altera
Series
Stratix®r
Datasheet
1.EP1S10F780C7.pdf
(276 pages)
Specifications of EP1S30F780C7
Number Of Logic Elements/cells
32470
Number Of Labs/clbs
3247
Total Ram Bits
3317184
Number Of I /o
597
Voltage - Supply
1.425 V ~ 1.575 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
780-FBGA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Other names
544-1421
EP1S30SF780C7
EP1S30SF780C7
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EP1S30F780C7
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Company:
Part Number:
EP1S30F780C7N
Manufacturer:
ALTERA30
Quantity:
144
Part Number:
EP1S30F780C7N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Power
Consumption
Altera Corporation
January 2006
Notes to
(1)
(2)
(3)
(4)
(5)
(6)
C
C
C
C
C
Table 4–33. Stratix Device Capacitance
IOTB
IOLR
CLKTB
CLKLR
CLKLR+
Symbol
When tx_outclock port of altlvds_tx megafunction is 717 MHz, V
Pin pull-up resistance values will lower if an external source drives the pin higher than V
Drive strength is programmable according to the values shown in the Stratix Architecture chapter of the Stratix
Device Handbook, Volume 1.
V
Capacitance is sample-tested only. Capacitance is measured using time-domain reflections (TDR). Measurement
accuracy is within ±0.5 pF.
V
REF
IO
and V
Tables 4–10
specifies the center point of the switching range.
CM
Input capacitance on I/O pins in I/O banks
3, 4, 7, and 8.
Input capacitance on I/O pins in I/O banks
1, 2, 5, and 6, including high-speed
differential receiver and transmitter pins.
Input capacitance on top/bottom clock input
pins:
Input capacitance on left/right clock inputs:
CLK1
Input capacitance on left/right clock inputs:
CLK0
have multiple ranges and values for J=1 through 10.
CLK[4:7]
,
,
through 4–33:
CLK3
CLK2
,
,
CLK8
CLK9
Altera
power calculator and the PowerGauge
software.
The interactive power calculator on the Altera web site is typically used
prior to designing the FPGA in order to get a magnitude estimate of the
device power. The Quartus II software PowerGauge feature allows you to
apply test vectors against your design for more accurate power
consumption modeling.
In both cases, these calculations should only be used as an estimation of
power, not as a specification.
Stratix devices require a certain amount of power-up current to
successfully power up because of the small process geometry on which
they are fabricated.
Table 4–34
power a Stratix device. This specification is for commercial operating
conditions. Measurements were performed with an isolated Stratix
device on the board to characterize the power-up current of an isolated
Parameter
and
,
, and
CLK10
CLK[12:15]
®
offers two ways to calculate power for a design: the Altera web
CLK11
Note (5)
shows the maximum power-up current (I
.
.
.
Minimum
O D ( m i n )
TM
Stratix Device Handbook, Volume 1
feature in the Quartus
Typical
DC & Switching Characteristics
11.5
11.5
8.2
7.8
4.4
= 235 mV on the output clock pin.
CCIO
CCINT
Maximum
.
) required to
®
II
Unit
pF
pF
pF
pF
pF
4–17