20-101-1112 Rabbit Semiconductor, 20-101-1112 Datasheet - Page 31

• Manufacturer Part Number: 20-101-1112
• Description: MODULE RABBITCORE RCM4010
• Manufacturer: Rabbit Semiconductor

Specifications of 20-101-1112

• Module/board Type: MPU Core Module
• Product: Microcontroller Modules
• Core Processor: Rabbit 4000
• Clock Speed: 58.98 MHz
• Interface Type: Ethernet, Serial
• Flash: 512 KB
• Timers: 10 x 8 bit, 1 x 10 bit, 1 x 16 bit
• Operating Supply Voltage: 3 V to 3.6 V
• Board Size: 47 mm x 61 mm x 20 mm
• Core: RCM4010
• Processor Series: RCM4000
• Silicon Manufacturer: Rabbit
• Core Architecture: Rabbit 4000
• Silicon Core Number: RCM4010
• Silicon Family Name: RCM4000
• Kit Contents: Board
• Development Tool Type: Hardware / Software - Dev Kit (Dev Tool)
• Rohs Compliant: Yes
• For Use With/related Products: RCM4010
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: Q3413688

User’s Manual
Follow the remaining steps carefully in Tera Term to avoid overwriting previously
saved calibration data when using same the file name.
Tera Term is now ready to log all data received on the serial port to the file you specified.
You are now ready to compile and run this sample program. A message will be displayed
in the Tera Term display window once the sample program is running.
Enter the serial number of your RabbitCore module in the Tera Term display window,
then press the
calibration data.
Now select
separate pop-up window minimized at the bottom of your PC screen. This finishes the
logging and closes the file.
Open your data file and verify that the calibration data have been written properly. A
sample is shown below.
Serial port transmission
========================
Uploading calibration table . . .
Enter the serial number of your controller = 9MN234
SN9MN234
ADSE
0
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
1
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
ADDF
0
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
2
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,float_gain,float_offset,
ADMA
3
float_gain,float_offset,
4
float_gain,float_offset,
END
|
|
|
|
|
|
CLOSE
•
•
ENTER
Enable the
Select the
•
•
•
Baud rate 19,200 bps, 8 bits, no parity, 1 stop bit
Enable
Feed options —
from within the Tera Term LOG window, which will likely be a
key. The Tera Term display window will now display the
OPEN
File APPEND
Local Echo
option at the right-hand side of the dialog box
Receive = CR
option
option at the bottom of the dialog box
,
Transmit = CR + LF
25