MPC8560CPX667JC Freescale Semiconductor, MPC8560CPX667JC Datasheet - Page 95

• Manufacturer Part Number: MPC8560CPX667JC
• Description: IC MPU PWRQUICC III 783-FCPBGA
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC IIIr

Specifications of MPC8560CPX667JC

• Processor Type: MPC85xx PowerQUICC III 32-Bit
• Speed: 667MHz
• Voltage: 1.2V
• Mounting Type: Surface Mount
• Package / Case: 783-FCPBGA
• Core Size: 32 Bit
• Program Memory Size: 64KB
• Cpu Speed: 667MHz
• Embedded Interface Type: I2C, MII, SPI, TDM, UTOPIA
• Digital Ic Case Style: BGA
• No. Of Pins: 783
• Rohs Compliant: No
• Family Name: MPC85XX
• Device Core: PowerQUICC III
• Device Core Size: 32b
• Frequency (max): 667MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 1.2V
• Operating Supply Voltage (max): 1.26V
• Operating Supply Voltage (min): 1.14V
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 783
• Package Type: FCBGA
• For Use With: MPC8560ADS-BGA - BOARD APPLICATION DEV 8560
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Lead Free Status / Rohs Status: Not Compliant

17.6 Configuration Pin Muxing
The MPC8560 provides the user with power-on configuration options which can be set through the use of
external pull-up or pull-down resistors of 4.7 kΩ on certain output pins (see customer visible configuration
pins). These pins are generally used as output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins
while HRESET is asserted, is latched when HRESET deasserts, at which time the input receiver is disabled
and the I/O circuit takes on its normal function. Most of these sampled configuration pins are equipped
with an on-chip gated resistor of approximately 20 kΩ. This value should permit the 4.7-kΩ resistor to pull
the configuration pin to a valid logic low level. The pull-up resistor is enabled only during HRESET (and
for platform/system clocks after HRESET deassertion to ensure capture of the reset value). When the input
receiver is disabled the pull-up is also, thus allowing functional operation of the pin as an output with
minimal signal quality or delay disruption. The default value for all configuration bits treated this way has
been encoded such that a high voltage level puts the device into the default state and external resistors are
needed only when non-default settings are required by the user.
Careful board layout with stubless connections to these pull-down resistors coupled with the large value
of the pull-down resistor should minimize the disruption of signal quality or speed for output pins thus
configured.
The platform PLL ratio and e500 PLL ratio configuration pins are not equipped with these default pull-up
devices.
17.7 Pull-Up Resistor Requirements
The MPC8560 requires high resistance pull-up resistors (10 kΩ is recommended) on open drain type pins
including EPIC interrupt pins. I
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in
state under normal operating conditions as most have asynchronous behavior and spurious assertion will
give unpredictable results.
TSEC1_TXD[3:0] must not be pulled low during reset. Some PHY chips have internal pulldowns that
could cause this to happen. If such PHY chips are used, then a pullup must be placed on these signals strong
enough to restore these signals to a logical 1 during reset.
Three test pins also require pull-up resistors (100 Ω - 1 kΩ). These pins are L1_TSTCLK, L2_TSTCLK,
and LSSD_MODE. These signals are for factory use only and must be pulled up to OVDD for normal
machine operation.
Refer to the PCI 2.2 specification for all pull-ups required for PCI.
Freescale Semiconductor
Figure
61. Care must be taken to ensure that these pins are maintained at a valid deasserted
MPC8560 Integrated Processor Hardware Specifications, Rev. 4.2
2
C open drain type pins should be pulled up with ~1 kΩ resistors.
System Design Information
95