ENC28J60-I/ML Microchip Technology, ENC28J60-I/ML Datasheet - Page 33

• Manufacturer Part Number: ENC28J60-I/ML
• Description: IC ETHERNET CTRLR W/SPI 28QFN
• Manufacturer: Microchip Technology

Specifications of ENC28J60-I/ML

• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Type: Ethernet Controller, MAC/10Base-T
• Interface: SPI
• Voltage - Supply: 3.1 V ~ 3.6 V
• Current - Supply: 160mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Input Voltage Range (max): 5.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.1 V to 3.6 V
• Supply Current (max): 180 mA
• Package: 28QFN EP
• Standard Supported: IEEE 802.3
• Communication Mode: Full Duplex|Half Duplex
• Network Interface: MII|MIIM
• Data Rate: 10 Mbps
• Host Interface: SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163024 - BOARD DEMO PICDEM.NET 2AC164123 - BOARD DAUGHTER ETH PICTAIL PLUSAC164121 - BOARD DAUGHTER PICTAIL ETHERNET
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.0
Before discussing the use of the ENC28J60 as an
Ethernet interface, it may be helpful to review the
structure of a typical data frame. Users requiring more
information should refer to the IEEE 802.3 standard
which is the basis for the Ethernet protocol.
5.1
Normal IEEE 802.3 compliant Ethernet frames are
between 64 and 1518 bytes long. They are made up of
five or six different fields: a destination MAC address, a
source MAC address, a type/length field, data payload,
an optional padding field and a Cyclic Redundancy
Check (CRC). Additionally, when transmitted on the
Ethernet medium, a 7-byte preamble field and Start-Of-
Frame (SOF) delimiter byte are appended to the
FIGURE 5-1:
© 2008 Microchip Technology Inc.
Note 1: The FCS is transmitted starting with bit 31 and ending with bit 0.
Used in the
Calculation
of the FCS
ETHERNET OVERVIEW
Packet Format
ETHERNET PACKET FORMAT
46-1500
of Bytes
Number
7
1
6
6
2
4
Type/Length
Preamble
Padding
FCS
Field
Data
SFD
DA
SA
(1)
Preliminary
beginning of the Ethernet packet. Thus, traffic seen on
the twisted-pair cabling will appear as shown in
Figure 5-1.
5.1.1
When transmitting and receiving data with the
ENC28J60, the preamble and Start-Of-Frame delimiter
bytes will automatically be generated or stripped from
the packets when they are transmitted or received. The
host controller does not need to concern itself with
them. Normally, the host controller will also not need to
concern itself with padding and the CRC which the
ENC28J60 will also be able to automatically generate
when transmitting and verify when receiving. The
padding and CRC fields will, however, be written into
the receive buffer when packets arrive, so they may be
evaluated by the host controller if needed.
Filtered Out by the Module
Start-Of-Frame Delimiter
(filtered out by the module)
Destination Address,
such as Multicast, Broadcast or Unicast
Source Address
Type of Packet or the Length of the Packet
Packet Payload
(with optional padding)
Frame Check Sequence – CRC
PREAMBLE/START-OF-FRAME
DELIMITER
Comments
ENC28J60
DS39662C-page 31