CY7C63801-PXC Cypress Semiconductor Corp, CY7C63801-PXC Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CY7C63801-PXC
Manufacturer Part Number
CY7C63801-PXC
Description
IC USB PERIPHERAL CTRLR 16-DIP
Manufacturer
Cypress Semiconductor Corp
Series
CY7Cr
Specifications of CY7C63801-PXC
Controller Type
USB Peripheral Controller
Interface
USB
Voltage - Supply
4 V ~ 5.5 V
Current - Supply
40mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
16-DIP (0.300", 7.62mm)
Operating Temperature (max)
70C
Operating Temperature (min)
0C
Operating Temperature Classification
Commercial
Package Type
MDIP
Mounting
Through Hole
Pin Count
16
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
770-1001 - ISP 4PORT CYPRESS ENCORE II MCUCY4623 - KIT MOUSE REFERENCE DESIGN428-1774 - EXTENSION KIT FOR ENCORE II428-1773 - KIT DEVELOPMENT ENCORE II
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Document 38-08035 Rev. *F
15.2
Table 15-2. SPI Configure Register (SPICR) [0x3D] [R/W]
Bit 7: Swap
0 = Swap function disabled
1 = The SPI block swaps its use of SMOSI and SMISO. Among other things, this can be useful in implementing single wire SPI-
like communications
Bit 6: LSB First
0 = The SPI transmits and receives the MSB (Most Significant Bit) first
1 = The SPI transmits and receives the LSB (Least Significant Bit) first.
Bit [5:4]: Comm Mode [1:0]
0 0: All SPI communication disabled
0 1: SPI master mode
1 0: SPI slave mode
1 1: Reserved
Bit 3: CPOL
This bit controls the SPI clock (SCLK) idle polarity
0 = SCLK idles low
1 = SCLK idles high
Bit 2: CPHA
The Clock Phase bit controls the phase of the clock on which data is sampled. Table 15-3 below shows the timing for the various
combinations of LSB First, CPOL, and CPHA
Bit [1:0]: SCLK Select
This field selects the speed of the master SCLK. When in master mode, SCLK is generated by dividing the base CPUCLK
Important Note for Comm Modes 01b or 10b (SPI Master or SPI Slave):
When configured for SPI, (SPI Use = 1—Table 14-15), the input/output direction of pins P1.3, P1.5, and P1.6 is set automati-
cally by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by firmware.
For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as an input.
Read/Write
Default
Field
Bit #
SPI Configure Register
Swap
R/W
7
0
LSB First
R/W
6
0
R/W
5
0
Comm Mode
R/W
4
0
CPOL
R/W
3
0
CPHA
R/W
2
0
R/W
1
0
CY7C63310
CY7C638xx
CY7C639xx
SCLK Select
Page 35 of 68
R/W
0
0
[+] Feedback