CY7C65640A-LFXC Cypress Semiconductor Corp, CY7C65640A-LFXC Datasheet - Page 10

• Manufacturer Part Number: CY7C65640A-LFXC
• Description: IC USB HUB CONTROLLER HS 56VQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: TetraHub™r

Specifications of CY7C65640A-LFXC

• Controller Type: USB Hub
• Interface: SPI Serial
• Voltage - Supply: 3.15 V ~ 3.45 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
• Current - Supply: 260mA
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3.15V
• Operating Supply Voltage (max): 3.45V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 56
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CY4602 - KIT USB 4-PORT HUB REF DESIGN
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 428-1805; CY7C65640A-LFXC

Table 10. Hub Descriptor
Document #: 38-08019 Rev. *J
Note
4. This value is configured through the External EEPROM.
Byte
3,4
0
1
2
5
6
7
8
All Speeds
0x0089
0xFF
0x04
0x32
0x64
0x00
0x09
0x29
[10]
[10]
[10]
[10]
[10]
[10]
bLength
bDescriptorType
bNbrPorts
wHubCharacteristics
bPwrOn2PwrGood
bHubContrCurrent
bDeviceRemovable
bPortPwrCtrlMask
Field Name
9 Bytes
HUB Descriptor
Number of ports supported
b1, b0: Logical Power Switching Mode
b2: Identifies a Compound Device,
b4, b3: Over-current Protection Mode
b6, b5: TT Think Time
b7: Port Indicators Supported,
b15...b8: Reserved
Time from when the port is powered to when the power is good on that port
Maximum current requirement for the Hub Controller
Indicates if the port has a removable device attached
Required for compatibility with software written for 1.0 compliant devices
00: Ganged power switching (all ports’ power at once)
01: Individual port power switching (Default in TetraHub)
0: Hub is not part of a compound device (Default in TetraHub),
1: Hub is part of a compound device.
00: Global Overcurrent Protection. The hub reports overcurrent as a
summation of all ports current draw, without a breakdown of individual port
overcurrent status.
01: Individual Port Overcurrent Protection. The hub reports overcurrent on
a per-port basis. Each port has an over-current status (Default in
TetraHub).
1X: No Overcurrent Protection. This option is allowed only for bus-
powered hubs that do not implement overcurrent protection.
00: TT requires at most 8 FS bit times of inter transaction gap on a
full-/low-speed downstream bus (Default in TetraHub).
01: TT requires at most 16 FS bit times.
10: TT requires at most 24 FS bit times.
11: TT requires at most 32 FS bit times.
0: Port Indicators are not supported on its downstream facing ports and
the PORT_INDICATOR request has no effect.
1: Port Indicators are supported on its downstream facing ports and the
PORT_INDICATOR request controls the indicators. See Section 4 and 9
(Default in TetraHub).
Description
CY7C65640A
Page 10 of 23
[+] Feedback