VQZ2121-5YZ1-N7T SMC Corporation, VQZ2121-5YZ1-N7T Datasheet - Page 73

no-image

VQZ2121-5YZ1-N7T

Manufacturer Part Number
VQZ2121-5YZ1-N7T
Description
Solenoid Valve, 5 port, body ported, 2 position sngl, 24VDC, DIN, 1/4 port
Manufacturer
SMC Corporation
Type
Solenoidr
Datasheet

Specifications of VQZ2121-5YZ1-N7T

Brand/series
VQZ Series
Configuration
2-Position Single
Number Of Ports
5
Primary Type
Solenoid Valve
Size, Port
1⁄4"
Voltage, Coil
24 VDC
Operating Pressure Range
15-100 PSI (30-100 PSI For Three Position Valves)
1. Conforming to ISO#: EN-175301-803C (Former
2. Connection
3. Changing the entry direction
4. Precautions
5. Compatible cable
Tightening torque
1.65 to 2.5 N m
Tightening torque
0.2 to 0.25 N m
DIN 43650C)
(8 mm between pins)
The DIN terminal type with an IP65 enclosure is protected
against dust and water, however, it must not be used in water.
1) Loosen the holding screw and pull the connector out of the
2) After removing the holding screw, insert a flat head screw-
3) Loosen the terminal screws (slotted screws) on the terminal
4) Secure the cord by fastening the ground nut.
After separating the terminal block and housing, the cord entry
can be changed by attaching the housing in the desired direc-
tion (4 directions at 90° intervals).
∗ When equipped with a light, be careful not to damage the
Plug in and pull out the connector vertically without tilting to
one side.
Cable O.D.: ø3.5 to ø7
(Reference) 0.5 mm
3306
Ground nut
light with the cord’s lead wires.
solenoid valve terminal block.
driver, etc. into the notch on the bottom of the terminal
block and pry it open, separating the terminal block and the
housing.
block, insert the cores of the lead wires into the terminals
according to the connection method, and fasten them se-
curely with the terminal screws.
Refer to the table.
(Rating symbol)
Washer
Grommet
(Rubber)
How to Use DIN Terminal
Terminal screw
(3 locations)
Series
Specific Product Precautions 3
Be sure to read this before handling.
For Safety Instructions and Common Precautions, refer to “Precautions for Handling
Pneumatic Devices” (M-03-E3A).
2
, 2-core or 3-core, equivalent to JIS C
VQZ
(Light mounting location)
Housing
Set screw
Terminal block
Notch
Tightening torque
0.3 to 0.4 N m
Without light
With light
Circuit diagram with light
Part no. for one-touch fitting for 1(P) port and silencer/one-touch
fitting for 3(R2, R), 5(R1) port
The diameter of the above fitting and silencer is the maximum diameter to
in the EXH port.
110 VAC (115 VAC)
220 VAC (230 VAC)
Fitting and Silencer Part No. for P, R Ports
AC circuit
VQZ1000
VQZ2000
VQZ3000
When Using Valve as an Individual Unit
Series
Rated voltage
Rated voltage
NL
1
All voltages
100 VAC
200 VAC
24 VDC
12 VDC
2
R
(1) One-touch fitting
NL: Neon light
fitting for 1(P) port
R: Resistor
(1) One-touch
DIN Connector Part No.
KQ2S06-01S
KQ2H08-02S
KQ2H06-M5
Voltage symbol
Voltage symbol
None
100 V
200 V
110 V
220 V
24 V
12 V
DC circuit
LED
AN120-M5
INA-25-46
AN101-01
1
Silencer
(2) For 3(R2, R) port, 5(R1) port
2
R
(2) Silencer
LED: Light emitting diode
SY100-82-3-05
SY100-82-3-06
SY100-82-2-01
SY100-82-2-02
SY100-82-2-03
SY100-82-2-04
R: Resistor
SY100-82-1
IN-457-32L (for ø6)
Part no.
Part no.
One-touch fitting
Back page 4
KQ2H06-01S
KJS04-M5

Related parts for VQZ2121-5YZ1-N7T