T1K-00010-466 NCC, T1K-00010-466 Datasheet
![no-image](/images/no-image-200.jpg)
T1K-00010-466
Manufacturer Part Number
T1K-00010-466
Description
Relay; Time Delay; Ctrl-V 12 VDC; Vol-Rtg 240 VAC; Cur-Rtg 10 A; DPDT; .1 to 10 sec.
Manufacturer
NCC
Datasheet
1.T1K-00010-461.pdf
(1 pages)
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: 800-323-2593 • 630-231-5900 • FAX: 630-231-1377 • www.nationalcontrols.com
1-6
Delay On Make
T1 Series
FEATURES
●
●
●
●
●
●
●
●
●
●
Operating Logic: Upon application of volt-
age to the input terminals, the time delay
cycle starts. At the end of the preset time
delay, the relay coil is energized and the
contacts transfer. Reset is accomplished by
the removal of input voltage.
Note: 1) Remote potentiometer leads should be shielded when
running close to other wires; 2) The minimum time setting on
external resistor-adjustable time delay relays is obtained by short-
ing together the external resistor terminals of the relay; 3) The
maximum time setting within tolerance limits is obtained by using
a 1 megohm resistor; 4) Timing values between the minimum
and maximum limits are linear with resistance within 10%; 5)
Recommend 1/4 W minimum resistor be used.
LOGIC FUNCTION DIAGRAM
ORDERING INFORMATION
* Optional Potentiometer: Part Number ASY-0001M-450
Input
Voltage
Relay
Coil
36 to 3600 sec.
1.8 to 180 sec.
TIME RANGE
3 to 300 sec.
6 to 600 sec.
.05 to 1 sec.
.1 to 10 sec.
.3 to 30 sec.
.6 to 60 sec.
100% functionally tested
Digital timing circuit
±1% repeatability
Time calibrated dial
Superior transient protection
Fiberglass reinforced circuit board
Internal components supported by
heavy-duty chassis
Reinforced base locator pin
Flame-retardant polycarbonate housing
On
Off
On
Off
TIME DELAY RELAYS
Delay On Make Function
File #E59090
T1K-00010-466
T1K-00030-466
T1K-00060-466
KNOB ADJST.
8-PIN BASE
12 VDC
Timing
—
—
—
—
—
T1K-00010-462
T1K-00060-462
KNOB ADJST.
8-PIN BASE
24 VDC
—
—
—
—
—
—
T1K-00010-467
T1K-00060-467
KNOB ADJST.
8-PIN BASE
24 VAC
—
—
—
—
—
—
SPECIFICATIONS
TIME DELAY
Adjustment: Knob or external resistor, factory
fixed on special order (min. order required)
Range: 50 ms to 1 hour in 8 ranges
Repeatability: ±1% at constant temperature
Accuracy: Maximum time -0%, +10%;
Minimum time +0%, -50%
Reset Time: 50 ms max. (25 ms typical)
INPUT
Operating Voltage: 24, 120, 240 VAC; 12, 24
VDC ±10% (DC models have reverse polarity pro-
tection. Unfiltered input voltage to them must be
full-wave rectified)
Power Consumption: 3 VA max.
Frequency: 50/60 Hz
OUTPUT
Type: Relay contacts, DPDT (2 form C)
Rating: 10 A max. resistive at 240 VAC; 100 mA
at 5 VDC min. load current
Life:
Mechanical: 10,000,000 operations
Full Load: 500,000 operations
PROTECTION
Transient Voltage: 12, 24 V timers are protected
by an 8.8 joule metal oxide varistor; 120, 240 V
timers are protected by a 30 joule metal oxide
varistor
Dielectric Breakdown: 1500 VAC, RMS min. at
60 Hz between input and outputs and between
outputs
MECHANICAL
Termination: 8-pin or 11-pin plug
Mounting: Socket mount, 8-pin part number
MSO-0008P-012; Socket mount, 11-pin part
number MSO-0011P-012
ENVIRONMENTAL
Storage Temperature: -23°C to 70°C
Operating Temperature: -23°C to 55°C
T1K-00001-461
T1K-00010-461 T1F-00010-461* T1K-00010-465
T1K-00030-461
T1K-00060-461 T1F-00060-461* T1K-00060-465
T1K-00180-461
T1K-00300-461
T1K-00600-461
T1K-03600-461
KNOB ADJST.
8-PIN BASE
120 VAC
REMOTE POT
11-PIN BASE
120 VAC
—
—
—
—
—
—
KNOB ADJST.
8-PIN BASE
240 VAC
—
—
—
—
—
—
External Resistance/Time Delay Relationship
1 megohm external resistance is required to obtain
the maximum time for all ranges. To determine the
actual resistance needed to obtain the required time
delay, use the following formula:
Note: Due to component tolerances, the actual time
obtained will normally be within 5% of desired time.
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
Rt=
.85
Tmaximum - Tminimum
Trequired - Tminimum
PIN CONFIGURATION
2
Polarity Shown is
2
Timing Resistor
for D.C. Models
3
1
3
(by Cust.)
Voltage
4
Voltage
1
4
Input
5
Input
1.75
6
2.90
5
7
11
8
7
6
8
9
10
(3012-1)
x 1,000,000 ohms
.53