VQZ115-5L1-N3 SMC Corporation, VQZ115-5L1-N3 Datasheet - Page 42
![no-image](/images/no-image-200.jpg)
VQZ115-5L1-N3
Manufacturer Part Number
VQZ115-5L1-N3
Description
Solenoid Valve, 3 port, body ported, 24VDC, L plug conn w/.3m lead, 5/32 fitting
Manufacturer
SMC Corporation
Type
Solenoidr
Datasheet
1.VQZ115-5L1-N7.pdf
(43 pages)
Specifications of VQZ115-5L1-N3
Brand/series
VQZ Series
Configuration
Body Ported
Number Of Ports
3
Primary Type
Solenoid Valve
Size, Port
5⁄32"
Voltage, Coil
24 VDC
Operating Pressure Range
15-100 PSI (30-100 PSI For Three Position Valves)
The built-in fittings on the manifold can be
changed easily. Simply remove the corre-
sponding valve and take out the fitting clip un-
derneath.
Take out the clip with a screwdriver, etc., then replace the fittings.
About mounting the fittings, after inserting the fitting until it stops,
then put the clip into the prescribed position.
VQZ200: Horizontally clipped to the valve body
VQZ100/300: Vertically clipped to the valve body
Precautions
When pulling the fitting assembly away from the valve base, re-
move the clip, then connect a tube or plug (KQ2P-) with the
one-touch fitting and pull it out holding the tube or plug. Do not
hold the release bushing to avoid damage.
1. Removing
2. Mounting
Back page 5
1) Loosen the clamp screw on
2) Lift the
1) Catch the hook of the DIN rail
2) Push side
Caution
Caution
the
manifold.
fold off the DIN rail and slide it
in the direction of the
bracket on the
DIN rail.
and tighten the clamp screw.
The proper tightening torque
for screws is 0.3 to 0.4 N m.
One-touch Fittings Replacement
side of both ends of the
DIN Rail Removal/Mounting
Fitting assembly
side
onto the DIN rail
Clip
Series
Specific Product Precautions 4
Be sure to read this before handling.
For Safety Instructions and 3 Port Solenoid Valve Precautions, refer to “Precautions for
Handling Pneumatic Devices” (M-03-E3A).
of the mani-
side on the
side.
Clip
VQZ
Clip
Fitting assembly
Clamp screw
Clamp bracket
Fitting assembly
1. After confirming the gasket is correctly
1. How to replace the port direction
Precautions
The clip length for the valve and the base are different. Fitting
may detach if the incorrect clip is used.
2.Valve piped on top can be operated indepen-
placed under the valve, securely tighten the
bolts with the proper torque shown in the ta-
ble below.
Fitting and port plug are modules. After removing the clip with
a flat head screwdriver, take out the fitting and port plug. The
piping direction (side or top) can be altered by exchanging the
fitting and port plug. During exchange, insert the fitting and the
port plug until they contact the wall, then, insert the clip to
specified position.
dently by using PR plate.
(Refer to the below part numbers when placing an order.)
Caution
VQZ100
VQZ200
VQZ300
Caution
Model
VQZ100 Piping Direction Replacement
VQZ100-12A (Standard)
VQZ100-12B (External pilot type)
∗ 2 set screws are included.
Proper tightening torque
0.13 to 0.19 N·m
0.25 to 0.35 N·m
0.5 to 0.7 N·m
Valve Mounting
PR plate
Fitting
Port plug
(VVQZ100-CP)
Screw
Clip