48132-51 AMETEK, 48132-51 Datasheet

48132-51

Manufacturer Part Number

48132-51

Description

24 Volt Brushless DC Motor Controller

Manufacturer

AMETEK

Type

Motor/Blowerr

Datasheet

1.48132-51.pdf (1 pages)

Specifications of 48132-51

Current, Input

5 A

Dimensions

92.7mmL×82.6mmW×24.9mmH

Mounting Type

Panel

Primary Type

Controller

Termination

Screw

Voltage, Supply

11 to 52 VDC

Lead Free Status / Rohs Status

RoHS Compliant part

For Use With

BLDC Motor

Current page: 1 of 1
Download datasheet (136Kb)

114

5 Amp BLDC Motor/Blower Controller

NOTES:

• Temperature: Operating: 0°C to 50°C, Storage Air: -40°C to 85°C.

• Speed Control: Electrical speed control is achieved by applying a 0 to 5 VDC signal on J1 Pin 3 with respect to J1 Pin 2. Mechanical speed control is achieved

• Current Control: 5 Amp RMS maximum.

Caution should be taken. Misplacement of jumper setting will destroy the control.

Jumper Settings:

*These part numbers are available through AMETEK Technical & Industrial Products distributors.

Maximum Continuous Current

Input Voltage Range

Controller PWM Frequency

Analog Speed Input

Electrical Hall Spacing

Waveform

Current Limit Protection

Rotation

by adjusting the potentiometer when J6 is in position 1 to 2.

J2-Motor Sensor Spacing: 120° electrical spacing with jumper connected (default).

J3-Rotations:

J5-Input Voltage:

J6-Speed Control:

J9:

(24.9)

(25.4)

MAX.

0.98

1.00

(43.2)

1.70

MAX.

CONNECTOR HOUSING 50-57-9408 OR EQUIVALENT

MATES WITH MOLEX 70066 SERIES G VERSION

INCH

(MM)

MOLEX 70553 SERIES RIGHT ANGLE HEADER

LOW PROFILE, SQUARE PIN, .100 CENTERS

Controller Data

MATES WITH AMP TERMINAL HOUSING

FRICTION LOCK HEADER, SQUARE PIN

MOLEX .156” PITCH RIGHT ANGLE

60° electrical spacing with jumper disconnected.

Clockwise rotation with jumper connected (default).

Counter-clockwise rotation with jumper disconnected.

Do not change while motor is running or damage will occur.

Position 1-2 for 16-52 VDC (default).

Position 2-3 for 11-16 VDC.

Position 1-2 for internal speed adjust, via on board potentiometer (default).

Position 2-3 for analog speed input, via 0-5 VDC signal applied to J1 pins 2 and 3.

F out provides a 0-12 VDC square wave to monitor speed

F out (Hz) =

8 CIRCUIT SEE CHART (J4)

3 CIRCUIT SEE CHART (J1)

770849-3 OR EQUIVALENT

(

MOLEX 6373 VERTICAL FRICTION LOCK HEADER

Motor RPM

120

MATES WITH MOLEX #22-01-2025

) (

(82.6±0.25)

3.25±.01

Poles

SQUARE PIN, .100 CENTER,

Motor

2 CIRCUIT SEE CHART (J9)

2.190±.015

(4.83±0.38)

(13.5±0.25)

)

.53±.01

.156±.010

(4±0.25)

Motor/Blower Contoller

(84.79±0.38)

(92.7±0.25)

3.338±.015

3.65±.01

6-Step Trapezoidal

C17

11-52 VDC

60° or 120°

CW / CCW

0-5 VDC

48132*

25 kHz

Yes

5 A

(4.83±0.25)

.190±.010

J1-1 Vin

J1-2 Vin Return (Gnd)

J1-3 Analog Speed In

J4-1 Motor Phase A

J4-2 Motor Phase C

J4-3 Hall - (Gnd)

J4-4 Hall 1

J4-5 Hall 2

J4-6 Hall 3

J4-7 Hall + (+12V)

J4-8 Motor Phase B

J9-1 Return (Gnd)

J9-2 Tach Out

Related parts for 48132-51

Related keywords

48132-51 datasheet
48132-51 data sheet
48132-51 pdf datasheet
48132-51 component
48132-51 part
48132-51 distributor
48132-51 RoHS
48132-51 datasheet download