S29GL512S10DHI020 Spansion Inc., S29GL512S10DHI020 Datasheet - Page 60

• Manufacturer Part Number: S29GL512S10DHI020
• Description: IC 512 MBIT, 3V, 100NS, 64-BALL FBGA, PAGE MODE
• Manufacturer: Spansion Inc.

Specifications of S29GL512S10DHI020

• Lead Free Status / Rohs Status: Supplier Unconfirmed

14. For PWDx, only one portion of the password can be programmed per each A0 command. Portions of the password must be programmed
15. All Lock Register bits are one-time programmable. The program state = 0 and the erase state = 1. Also, both the Persistent Protection
16. If any of the Entry commands was issued, an Exit command must be issued to reset the device into read mode.
17. Protected State = 00h, Unprotected State = 01h. The sector address for DYB set, DYB clear, or PPB Program command may be any
6.2
60
in sequential order (PWD0 - PWD3).
Mode Lock Bit and the Password Protection Mode Lock Bit cannot be programmed at the same time or the Lock Register Bits Program
operation aborts and returns the device to read mode. Lock Register bits that are reserved for future use are undefined and may be 0’s or
1's.
location within the sector - the lower order bits of the sector address are don't care.
Device ID and Common Flash Interface (ID-CFI) ASO Map
The Device ID portion of the ASO (word locations 0h to 0Fh) provides manufacturer ID, device ID, Sector
Protection State, and basic feature set information for the device.
ID-CFI Location 02h displays sector protection status for the sector selected by the sector address (SA) used
in the ID-CFI enter command. To read the protection status of more than one sector it is necessary to exit the
ID ASO and enter the ID ASO using the new SA. The access time to read location 02h is always t
read of this location requires CE# to go High before the read and return Low to initiate the read
(asynchronous read access). Page mode read between location 02h and other ID locations is not supported.
Page mode read between ID locations other than 02h is supported.
For additional information see
Manufacture ID
Indicator Bits
Description
Verification
Protection
Device ID
RFU
(SA) + 000Ah
(SA) + 000Bh
(SA) + 0000h
(SA) + 0001h
(SA) + 0002h
(SA) + 0003h
(SA) + 0004h
(SA) + 0005h
(SA) + 0006h
(SA) + 0007h
(SA) + 0008h
(SA) + 0009h
D a t a
Address
Table 6.2 ID (Autoselect) Address Map (Sheet 1 of 2)
ID-CFI ASO on page
S h e e t
GL-S MirrorBit
0001h
227Eh
is shown only for the SA selected when entering ID-CFI ASO. Reading other SA provides
undefined data. To read a different SA protection state ASO exit command must be used
and then enter ID-CFI ASO again with the new SA.
DQ15-DQ08 = 1 (Reserved)
DQ7 - Factory Locked Secure Silicon Region
DQ6 - Customer Locked Secure Silicon Region
DQ5 = 1 (Reserved)
DQ4 - WP# Protects
DQ3 - DQ0 = 1 (Reserved)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Sector Protection State (1= Sector protected, 0= Sector unprotected). This protection state
1 = Locked,
0 = Not Locked
1 = Locked
0 = Not Locked
0 = lowest address Sector
1 = highest address Sector
( A d v a n c e
®
Family
35.
I n f o r m a t i o n )
S29GL_128S_01GS_00_01 February 11, 2011
Read Data
ACC
and a