AD7869JR Analog Devices Inc, AD7869JR Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD7869JR
Manufacturer Part Number
AD7869JR
Description
IC I/O PORT 14BIT ANLG 28-SOIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD7869JR.pdf
(16 pages)
Specifications of AD7869JR
Rohs Status
RoHS non-compliant
Applications
Analog I/O
Interface
TTL/CMOS
Voltage - Supply
4.75 V ~ 5.25 V
Package / Case
28-SOIC (7.5mm Width)
Mounting Type
Surface Mount
Converter Type
ADC/DAC
Resolution
14b
Data Rate
0.083MSPS
Digital Interface Type
Serial
Pin Count
28
Package Type
SOIC W
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7869JR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7869JRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD7869 DYNAMIC SPECIFICATIONS
The AD7869 is specified and 100% tested for dynamic perfor-
mance specifications as well as traditional dc specifications such
as Integral and Differential Nonlinearity. These ac specifications
are required for signal processing applications such as speech
recognition, spectrum analysis and high speed modems. These
applications require information on the converter’s effect on the
spectral content of the input signal. Hence, the parameters for
which the AD7869 is specified include SNR, harmonic distor-
tion and peak harmonics. These terms are discussed in more de-
tail in the following sections.
Signal-to-Noise Ratio (SNR)
SNR is the measured signal-to-noise ratio at the output of the
ADC or DAC. The signal is the rms magnitude of the funda-
mental. Noise is the rms sum of all the nonfundamental signals
up to half the sampling frequency (f
SNR is dependent upon the number of levels used in the quanti-
zation process; the more levels, the smaller the quantization
noise. The theoretical signal-to-noise ratio for a sine wave input
is given by
where N is the number of bits. Thus for an ideal 14-bit con-
verter, SNR = 86 dB.
Effective Number of Bits
The formula given in Equation (1) relates the SNR to the num-
ber of bits. Rewriting the formula, as in Equation (2), it is pos-
sible to obtain a measure of performance expressed in effective
number of bits (N).
The effective number of bits for a device can be calculated di-
rectly from its measured SNR.
Harmonic Distortion
Harmonic Distortion is the ratio of the rms sum of harmonics to
the fundamental. For the AD7869, total harmonic distortion
(THD) is defined as:
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5 and V6 are the rms amplitudes of the second through to
the sixth harmonic. The THD is also derived from the FFT plot
of the ADC or DAC output spectrum.
ADC Testing
The output spectrum from the ADC is evaluated by applying a
sine wave signal of very low distortion to the V
reading multiple conversion results. A Fast Fourier Transform
(FFT) plot is generated from which the SNR data can be ob-
tained. Figure 9 shows a typical 2048 point FFT plot of the
AD7869AQ ADC with an input signal of 10 kHz and a sam-
pling frequency of 60 kHz. The SNR obtained from this graph
is 80 dB. It should be noted that the harmonics are taken into
account when calculating the SNR.
REV. A
SNR = (6.02N + 1.76) dB
THD 20 log
N
SNR –1.76
6.02
V
2
2
V
3
2
SAMPLE
V
V
1
4
2
/2), excluding dc.
V
5
2
IN
V
input while
6
2
(1)
(2)
–9–
Figure 10 shows a typical plot of effective number of bits versus
frequency for an AD7869AQ with a sampling frequency of
60 kHz. The effective number of bits typically falls between 12.7
and 13.1, corresponding to SNR figures of 79 dB and 80.4 dB.
DAC Testing
A simplified diagram of the method used to test the dynamic
performance specifications of the DAC is outlined in Figure 11.
Data is loaded to the DAC under control of the microcontroller
and associated logic. The output of the DAC is applied to a 9th
order low pass filter whose cutoff frequency corresponds to the
Nyquist limit. The output of the filter is, in turn, applied to a
16-bit accurate digitizer. This digitizes the signal and the micro-
controller generates an FFT plot from which the dynamic per-
formance of the DAC can be evaluated.
Figure 10. Effective Number of Bits vs. Frequency for the
ADC
CONTROLLER
Figure 11. DAC Dynamic Performance Test Circuit
MICRO-
Figure 9. ADC FFT Plot
AD7869
DAC
LOW-PASS
FILTER
AD7869
DIGITIZER
16-BIT