CB-OWS451X-04-0 ConnectBlue, CB-OWS451X-04-0 Datasheet - Page 23

• Manufacturer Part Number: CB-OWS451X-04-0
• Description: RF SERIAL PORT ADAPTER U.FL
• Manufacturer: ConnectBlue
• Series: CB-OWSr

Specifications of CB-OWS451X-04-0

• Frequency: 2.4GHz, 5GHz
• Data Rate - Maximum: 115 kbps
• Modulation Or Protocol: 802.11 a/b/g/n
• Applications: General Purpose
• Power - Output: 20dBm (100mW)
• Sensitivity: -89dBm
• Voltage - Supply: 3.3 V ~ 5.5 V
• Current - Receiving: -
• Current - Transmitting: -
• Data Interface: Solder Pad
• Memory Size: -
• Antenna Connector: U.FL x 2
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Modular
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 809-1041

connectBlue
Copyright © 2010 connectBlue AB
This device has been designed to operate with an antenna having a maximum gain of +8.5 dBi. Having a higher gain is strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropic
radiated power (EIRP) is not more than that required for successful communication.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of
Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's website
http://www.hc-sc.gc.ca/rpb
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
For an end product using the product there MUST be a label containing, at least, the following information:
The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the
modular approval guidelines developed by the FCC. In accordance with 47 CFR § 15.19 the end product shall bear the following
statement in a conspicuous location on the device:
"This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
When the device is so small or for such use that it is not practicable to place the statement above on it, the information shall be placed in
a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which
the device is marketed. However, the FCC ID label must be displayed on the device. In case, where the final product will be installed in
locations where the end-user is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in
the end-product manual.
Our module types cB-OWL253 and cB-OWS451 are for OEM integrations only. In the end-user product the module shall be
professionally installed in such a manner that only the authorized antennas can be used.
This device contains
FCC ID: PVH0942
IC: 5325A-0942
7.3.2 FCC statement
7.3.2.1 Labeling requirements for end product
7.3.2.2 Antenna
7.3.2.3 Caution
1.
2.
this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation."
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications NOT explicitly APPROVED by connectBlue AB could cause the module to cease to
comply with FCC rules part 15, and thus void the user's authority to operate the equipment.
Within the 5180 to 5240 MHz band (5 GHz radio channels 34 to 48) the module types cB-OWL253 and cB-OWS451
are restricted to indoor operations.
§15.407 statement; in case of absence of information to transmit or operational failure the modules types cB-OWL253
and cB-OWS451 will automatically discontinue transmission.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
.
Page 23 of 26