XRP7714ILB-0X18-F Exar Corporation, XRP7714ILB-0X18-F Datasheet - Page 17

• Manufacturer Part Number: XRP7714ILB-0X18-F
• Description: IC CTRLR PWM/LDO STP-DWN 40TQFN
• Manufacturer: Exar Corporation
• Series: -r

Specifications of XRP7714ILB-0X18-F

• Topology: Step-Down (Buck) Synchronous (4), Linear (LDO) (1)
• Function: Any Function
• Number Of Outputs: 5
• Frequency - Switching: 1.5MHz
• Voltage/current - Output 1: Controller
• Voltage/current - Output 2: Controller
• Voltage/current - Output 3: Controller
• W/led Driver: No
• W/supervisor: No
• W/sequencer: Yes
• Voltage - Supply: 4.75 V ~ 25 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: *
• Package / Case: *
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1699

O
The Over-Voltage Protection (OVP) SET_OVVP_REGISTER sets the over-voltage condition in
predefined steps per channel. The over-voltage protection is always active even during soft-start
condition. When the over-voltage condition is tripped, the controller will shut down the channel.
When the channel is shut down the controller will then set corresponding OVP Fault bits in the
READ_OVV_UVLO_OVT_FLAG register.
The VOUT OVP Threshold is 150mV to 300mV above nominal VOUT for a Voltage Target of 2.5V or
less. For the Voltage Target of 2.6V to 5.1V, the VOUT OVP Threshold is 300mV to 600mV.
Once
SET_FAULT_RESP_CONFIG_LB and SET_FAULT_RESP_CONFIG_HB to determine whether there are
any “following” channels that need to be shut down. Any following channel will be disabled when
the channel with the Over Voltage Fault is disabled. The channel(s) will remain disabled, until the
Host takes action to enable the channel(s).
Any of the fault and warning conditions can also be configured to be represented using the general
purpose input output pins (GPIO) to use as an interface with non I
further information on this topic see the “GPIO Pins” Section.
During OVP fault shutdown of the channel, the customer has the option to choose two types of
shutdown for each channel. The first shutdown is ‘passive shutdown’ where the IC merely stops
outputting pulses. The second shutdown is a ‘brute force’ shutdown where the GL remains on as
the channel reaches its discharged voltage. Note that if the ‘brute force’ method is chosen, then GL
will permanently remain high until the channel is re-enabled.
O
XRP7714 utilizes a low side MOSFET Rdson current sensing technique. The voltage drop on Rdson
is measured by dedicated current ADC. The ADC results are compared to a maximum current
threshold and an over-current warning threshold to generate the fault and warning flags.
The
SET_ISENSE_PARAM_CHx register. The SET_VIOUT_MAX_CHx register is an 8 bit register.
[5:0] set the maximum current threshold and bits [7:6] set the over-current warning threshold.
The LSB for the current limit register is 5 mV and the allowed voltage range is between 0 and
315mV. To calculate the maximum current limit, the user needs to provide the MOSFET Rdson. The
maximum current can be calculated as:
Where Kt is the temperature coefficient of the MOSFET Rdson; Vsense is the voltage across Rdson;
IOUTMAX is the maximum output current.
The XRP7714 also offers an Over-Current warning flag. This warning flag resides in the
READ_OVC_FLAG register. The warning flag bit will be set when the output current gets to within a
specified value of the output current limit threshold enabling the host to reduce power
consumption. The SET_VIOUT_MAX_CHx register allows the warning flag threshold to be set 10mV,
20mV, 30mV or 40mV below VIOUT_MAX. The warning flag will be automatically cleared when the
current drops below the warning threshold.
© 2011 Exar Corporation
Maximum Output Current
Over-Current Warning
VER
UTPUT
-V
maximum
OLTAGE
the
C
URRENT
over-voltage
P
ROTECTION
output
S
ETTING AND
current
(OVP)
Channel
M
Q
Q
ONITORING
u
u
a
a
is
�������������� =
d
d
C
C
is
set
h
h
a
a
17/29
n
n
disabled,
by
n
n
���������� × ����
e
e
l
������������
l
D
D
the
i
i
g
g
i
i
t
t
SET_VIOUT_MAX_CHx
a
a
the
l
l
P
P
W
W
controller
M
M
S
S
2
C compatible devices. For
t
t
e
e
p
p
D
D
o
o
will
w
w
n
n
X
X
register
C
C
check
R
R
o
o
n
P
n
P
Rev. 1.1.6
t
t
7
7
r
r
o
o
7
7
l
l
1
1
and
Bits
l
l
the
e
e
4
4
r
r