LH28F800BJHE-PBTL90 Sharp Electronics, LH28F800BJHE-PBTL90 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LH28F800BJHE-PBTL90
Manufacturer Part Number
LH28F800BJHE-PBTL90
Description
Manufacturer
Sharp Electronics
Datasheet
1.LH28F800BJHE-PBTL90.pdf
(58 pages)
Specifications of LH28F800BJHE-PBTL90
Cell Type
NOR
Density
8Mb
Access Time (max)
90ns
Interface Type
Parallel
Boot Type
Bottom
Address Bus
20/19Bit
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
-40C to 85C
Package Type
TSOP
Sync/async
Asynchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8/16Bit
Number Of Words
1M/512K
Supply Current
30mA
Mounting
Surface Mount
Pin Count
48
Lead Free Status / Rohs Status
Not Compliant
1 INTRODUCTION
This datasheet contains the product specifications. Section
1 provides a flash memory overview. Sections 2, 3, 4 and
5 describe the memory organization and functionality.
Section 6 covers electrical specifications.
1.1 Features
Key enhancements of the product are:
Please note following:
1.2 Product Overview
The product is a high-performance 8M-bit Boot Block
Flash memory organized as 512K-word of 16 bits or 1M-
byte of 8 bits. The 512K-word/1M-byte of data is arranged
in two 4K-word/8K-byte boot blocks, six 4K-word/8K-
byte parameter blocks and fifteen 32K-word/64K-byte
main blocks which are individually erasable, lockable and
unlockable in-system. The memory map is shown in
Figure 3.
The dedicated V
when V
A Command User Interface (CUI) serves as the interface
between the system processor and internal operation of the
device. A valid command sequence written to the CUI
initiates device automation. An internal Write State
Machine (WSM) automatically executes the algorithms
and timings necessary for block erase, full chip erase,
word/byte write and lock-bit configuration operations.
sharp
•Single low voltage operation
•Low power consumption
•Enhanced Suspend Capabilities
•Boot Block Architecture
•V
3.6V block erase, full chip erase, word/byte write and
lock-bit configuration operations. The V
transitions to GND is recommended for designs that
switch V
CCWLK
CCW
CCW
≤V
has been lowered to 1.0V to support 2.7V-
CCWLK
CCW
off during read operation.
.
pin gives complete data protection
CCW
voltage
LHF80J05
A block erase operation erases one of the device’s 32K-
word/64K-byte blocks typically within 1.2s (3V V
V
V
can be independently erased minimum 100,000 times.
Block erase suspend mode allows system software to
suspend block erase to read or write data from any other
block.
Writing memory data is performed in word/byte
increments of the device’s 32K-word blocks typically
within 33µs (3V V
typically within 31µs (3V V
blocks typically within 36µs (3V V
byte blocks typically within 32µs (3V V
Word/byte write suspend mode enables the system to read
data or execute code from any other flash memory array
location.
Individual block locking uses a combination of bits, thirty-
nine block lock-bits, a permanent lock-bit and WP# pin, to
lock and unlock blocks. Block lock-bits gate block erase,
full chip erase and word/byte write operations, while the
permanent lock-bit gates block lock-bit modification and
locked
operations (Set Block Lock-Bit, Set Permanent Lock-Bit
and Clear Block Lock-Bits commands) set and cleared
lock-bits.
The status register indicates when the WSM’s block erase,
full chip erase, word/byte write or lock-bit configuration
operation is finished.
The RY/BY# output gives an additional indicator of WSM
activity by providing both a hardware signal of status
(versus software polling) and status masking (interrupt
masking for background block erase, for example). Status
polling using RY/BY# minimizes both CPU overhead and
system power consumption. When low, RY/BY# indicates
that the WSM is performing a block erase, full chip erase,
word/byte write or lock-bit configuration. RY/BY#-high Z
indicates that the WSM is ready for a new command,
block erase is suspended (and
inactive), word/byte write is suspended, or the device is in
reset mode.
CCW
CC
, 3V V
), 4K-word/8K-byte blocks typically within 0.6s (3V
block
CCW
) independent of other blocks. Each block
alternation.
CC
, 3V V
CC
CCW
Lock-bit
, 3V V
CC
word/byte write is
), 64K-byte blocks
, 3V V
CC
CCW
, 3V V
configuration
), 4K-word
CCW
Rev. 1.27
CC
CCW
), 8K-
, 3V
).
3