LH28F320BFHE-PBTLF1 Sharp Electronics, LH28F320BFHE-PBTLF1 Datasheet
LH28F320BFHE-PBTLF1
Specifications of LH28F320BFHE-PBTLF1
Related parts for LH28F320BFHE-PBTLF1
LH28F320BFHE-PBTLF1 Summary of contents
Page 1
... RELIMINARY RODUCT PECIFICATION LH28F320BFHE-PBTLF1 Flash Memory 32Mbit (2Mbitx16) (Model Number: LHF32FF1 Spec. Issue Date: October 15, 2004 Lead-free (Pb-free) Spec No: EL16X114 Integrated Circuits Group ...
Page 2
...
Page 3
Handle this document carefully for it contains material protected by international copyright law. Any reproduction, full or in part, of this material is prohibited without the express written permission of the company. • When using the products covered herein, ...
Page 4
TSOP Pinout................................................. 3 Pin Descriptions.......................................................... 4 Simultaneous Operation Modes Allowed with Four Planes .................................. 5 Memory Map .............................................................. 6 Identifier Codes and OTP Address for Read Operation ............................................. 7 Identifier Codes and OTP Address for Read Operation on Partition ...
Page 5
... LH28F320BFHE-PBTLF1 Page Mode Dual Work Flash MEMORY 32M density with 16Bit I/O Interface High Performance Reads • 80/35ns 8-Word Page Mode Configurative 4-Plane Dual Work • Flexible Partitioning • Read operations during Block Erase or (Page Buffer) Program • Status Register for Each Partition Low Power Operation • ...
Page 6
WE# 11 RST WP ...
Page 7
... Use of this pin at 12V beyond these limits may reduce block cycling capability or cause permanent damage. DEVICE POWER SUPPLY (2.7V-3.6V): With V V SUPPLY flash memory are inhibited. Device operations at invalid V CC Characteristics) produce spurious results and should not be attempted. INPUT/OUTPUT POWER SUPPLY (2.7V-3.6V): Power supply for all input/output V ...
Page 8
Table 2. Simultaneous Operation Modes Allowed with Four Planes THEN THE MODES ALLOWED IN THE OTHER PARTITION IS: IF ONE Read Read Read PARTITION IS: Array ID/OTP Status Read Array X X Read ID/OTP X X Read Status X X ...
Page 9
BLOCK NUMBER ADDRESS RANGE 70 32K-WORD 1F8000H - 1FFFFFH 69 32K-WORD 1F0000H - 1F7FFFH 68 32K-WORD 1E8000H - 1EFFFFH 67 32K-WORD 1E0000H - 1E7FFFH 66 32K-WORD 1D8000H - 1DFFFFH 65 32K-WORD 1D0000H - 1D7FFFH 64 32K-WORD 1C8000H - 1CFFFFH 63 ...
Page 10
Table 3. Identifier Codes and OTP Address for Read Operation Manufacturer Code Manufacturer Code Device Code Bottom Parameter Device Code Block Lock Configuration Block is Unlocked Code Block is Locked Block is not Locked-Down Block is Locked-Down Device Configuration Code ...
Page 11
LHF32FF1 [ 000088H Customer Programmable Area 000085H 000084H Factory Programmed Area 000081H Reserved for Future Implementation 000080H (DQ - Customer Programmable Area Lock Bit (DQ Factory Programmed Area Lock Bit (DQ Figure 3. OTP ...
Page 12
Table 5. Bus Operation Mode Notes RST# CE# Read Array Output Disable V IH Standby V IH Reset Read Identifier Codes/OTP V Read Query 6,7 IH Write 4,5 NOTES: ...
Page 13
... OTP block (See Table 3 and Table 4). The Read Query command is available for reading CFI (Common Flash Interface) information. 5. Block erase, full chip erase or (page buffer) program cannot be executed when the selected block is locked. Unlocked block can be erased or programmed when RST ...
Page 14
LH28F320BF series for details the program operation in one partition is suspended and the erase operation in other partition is also suspended, the suspended program operation should be resumed first, and then the suspended erase operation should be ...
Page 15
Table 7. Functions of Block Lock Current State (1) State WP [000 ( [001] [011 [100 ( [101] ( [110] [111 NOTES: 1. ...
Page 16
Table 9. Block Locking State Transitions upon WP# Transition Current State Previous State State WP# - [000 [001] 0 (2) [110] [011] 0 (2) Other than [110] - [100 [101 [110 [111] ...
Page 17
WSMS BESS BEFCES 7 6 SR.15 - SR.8 = RESERVED FOR FUTURE ENHANCEMENTS (R) SR.7 = WRITE STATE MACHINE STATUS (WSMS Ready 0 = Busy SR.6 = BLOCK ERASE SUSPEND STATUS (BESS) 1 ...
Page 18
SMS XSR.15-8 = RESERVED FOR FUTURE ENHANCEMENTS (R) XSR.7 = STATE MACHINE STATUS (SMS Page Buffer Program available 0 = Page Buffer Program not available XSR.6-0 = RESERVED FOR FUTURE ...
Page 19
Table 12. Partition Configuration Register Definition PCR.15-11 = RESERVED FOR FUTURE ENHANCEMENTS (R) PCR.10-8 = PARTITION CONFIGURATION (PC2-0) 000 = No partitioning. Dual Work is not allowed. 001 = Plane1-3 are ...
Page 20
Electrical Specifications 1.1 Absolute Maximum Ratings Operating Temperature During Read, Erase and Program ...-40°C to +85°C Storage Temperature During under Bias............................... -40°C to +85°C During non Bias................................ -65°C to +125°C Voltage On Any Pin (except V and V ).............. ...
Page 21
Capacitance (T =+25°C, f=1MHz) A Parameter Symbol Input Capacitance C IN Output Capacitance C OUT NOTE: 1. Sampled, not 100% tested. 1.2.2 AC Input/Output Test Conditions V CCQ INPUT 0.0 AC test inputs are driven at V Input ...
Page 22
DC Characteristics Symbol Parameter I Input Load Current LI I Output Leakage Current Standby Current CCS Automatic Power Savings Current CCAS Reset Power-Down Current CCD CC Average V Read CC ...
Page 23
Symbol Parameter V Input Low Voltage IL V Input High Voltage IH V Output Low Voltage OL V Output High Voltage OH V Lockout during Normal PP V PPLK Operations V during Block Erase, Full Chip PP V Erase, (Page ...
Page 24
AC Characteristics - Read-Only Operations Symbol t Read Cycle Time AVAV t Address to Output Delay AVQV t CE# to Output Delay ELQV t Page Address Access Time APA t OE# to Output Delay GLQV t RST# High to ...
Page 25
(A) 20 EHEL V IH (E) CE AVEL t t GHGL V IH OE# ( (W) WE High (D/Q) 15-0 V ...
Page 26
(A) 20 (A) 2 CE# ( OE# ( WE# ( High (D/Q) 15-0 V ...
Page 27
(A) 20 AVQV V IH VALID A (A) 2-0 ADDRESS CE# ( ELQV V IH OE# ( WE# ( GLQX ...
Page 28
AC Characteristics - Write Operations Symbol t Write Cycle Time AVAV RST# High Recovery to WE# (CE#) Going Low PHWL PHEL CE# (WE#) Setup to WE# (CE#) Going Low ELWL WLEL t (t ...
Page 29
NOTE 1 NOTE VALID A (A) 20-0 ADDRESS (E) CE ELWL WLEL V IH OE# ( PHWL PHEL V IH WE# (W) V ...
Page 30
Reset Operations V IH RST# ( High (D/Q) 15 RST# ( High (D/Q) 15 (min GND V ...
Page 31
Block Erase, Full Chip Erase, (Page Buffer) Program and OTP Program Performance Symbol Parameter 4K-Word Parameter Block t WPB Program Time 32K-Word Main Block t WMB Program Time t / WHQV1 Word Program Time t EHQV1 t / WHOV1 ...
Page 32
Related Document Information Document No. FUM00701 NOTE: 1. International customers should contact their local SHARP or distribution sales offices. LHF32FF1 (1) Document Name LH28F320BF series Appendix 29 Rev. 2.44 ...
Page 33
...
Page 34
...
Page 35
...
Page 36
...
Page 37
...
Page 38
...
Page 39
...
Page 40
...
Page 41
...
Page 42
A-1 RECOMMENDED OPERATING CONDITIONS A-1.1 At Device Power-Up AC timing illustrated in Figure A-1 is recommended for the supply voltages and the control signals at device power-up. If the timing in the figure is ignored, the device may not operate ...
Page 43
A-1.1.1 Rise and Fall Time Symbol t V Rise Time Input Signal Rise Time R t Input Signal Fall Time F NOTES: 1. Sampled, not 100% tested. 2. This specification is applied for not only the device ...
Page 44
A-1.2 Glitch Noises Do not input the glitch noises which are below V as shown in Figure A-2 (b). The acceptable glitch noises are illustrated in Figure A-2 (a). Input Signal V (Min (Max.) IL Input Signal (a) ...
Page 45
... A-2 RELATED DOCUMENT INFORMATION Document No. AP-001-SD-E Flash Memory Family Software Drivers AP-006-PT-E Data Protection Method of SHARP Flash Memory RP#, V AP-007-SW-E NOTE: 1. International customers should contact their local SHARP or distribution sales office. (1) Document Name Electric Potential Switching Circuit PP iv Rev. 1.10 ...
Page 46
A-3 STATUS REGISTER READ OPERATIONS If AC timing for reading the status register described in specifications is not satisfied, a system processor can check the status register bit SR.15 instead of SR.7 to determine when the erase or program operation ...
Page 47
... Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE SHARP Electronics (Singapore) PTE., Ltd. ...