CS4299-JQ Cirrus Logic Inc, CS4299-JQ Datasheet - Page 36
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS4299-JQ
Manufacturer Part Number
CS4299-JQ
Description
Audio Codec 1ADC / 1DAC 18-Bit/20-Bit 48-Pin LQFP
Manufacturer
Cirrus Logic Inc
Type
PCMr
Datasheet
1.CS4299-JQ.pdf
(52 pages)
Specifications of CS4299-JQ
Package
48LQFP
Adc/dac Resolution
18/20 Bit
Number Of Channels
1ADC /1 DAC
Sampling Rate
48 KSPS
Number Of Adc Inputs
8
Number Of Dac Outputs
3
Number Of Dacs
1
Operating Supply Voltage
3.3|5 V
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS4299-JQ
Manufacturer:
CAYSTRL
Quantity:
5 510
Company:
Part Number:
CS4299-JQ
Manufacturer:
CRYSTAL
Quantity:
624
Company:
Part Number:
CS4299-JQEP
Manufacturer:
CAYSTRL
Quantity:
5 510
Company:
Part Number:
CS4299-JQEP
Manufacturer:
ST
Quantity:
5 510
Company:
Part Number:
CS4299-JQEP
Manufacturer:
CRYSTAL
Quantity:
210
Part Number:
CS4299-JQEP
Manufacturer:
CRYSTAL
Quantity:
20 000
Part Number:
CS4299-JQZ
Manufacturer:
CIRRUS
Quantity:
20 000
Company:
Part Number:
CS4299-JQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
6. ANALOG HARDWARE
The analog line-level input hardware consists of
four stereo inputs (LINE_IN_L/R, CD_L/GND/R,
VIDEO_L/R, and AUX_L/R), two selectable
mono microphone inputs (MIC1 and MIC2), and
two mono inputs (PC_BEEP and PHONE). The an-
alog line-level output hardware consists of a mono
output (MONO_OUT), and dual stereo line outputs
(LINE_OUT_L/R and ALT_LINE_OUT_L/R).
This section describes the analog hardware needed
to interface with these pins. The designs presented
in this section comply with specifications detailed
in Chapter 17 of the Microsoft
lines [7] (referred to as PC 99). For EMI reduction
techniques refer to the application note N165:
CS4297A/CS4299 EMI Reduction Techniques [5].
6.1
All analog inputs to the CS4299, including
CD_GND, should be capacitively coupled to the
input pins. Unused analog inputs should be tied to-
gether and connected through a capacitor to analog
ground or tied to the Vrefout pin directly. The max-
imum allowed voltage for analog inputs, except the
microphone input, is 1 V
input the maximum allowed voltage depends on the
selected boost setting.
6.1.1
Figure 10 shows circuitry for a line-level stereo in-
put. Replicate this circuit for the Line, Video and
Aux inputs. This design attenuates the input by
6 dB, bringing the signal from the PC 99 specified
2 V
6.1.2
The CD line-level input has an extra pin,
CD_GND, providing a pseudo-differential input
for both CD_L and CD_R. This pin takes the
common-mode noise out of the CD inputs when
36
36
RMS
DESCRIPTION
, to the CS4299 maximum allowed 1 V
Analog Inputs
Line-Level Inputs
CD Input
RMS
. For the microphone
PC Design Guide-
RMS
.
connected to the CD analog source ground. Follow-
ing the reference designs in Figure 11 and
Figure 12 provides extra attenuation of common
mode noise coming from the CD-ROM drive,
thereby producing a higher quality signal. One per-
cent resistors are recommended since closely
matched resistor values provide better com-
mon-mode attenuation of unwanted signals. The
circuit shown in Figure 11 can be used to attenuate
a 2 V
shown in Figure 12 can be used for a 1 V
put signal.
CD_COM
CD_COM
Figure 10. Line Input (Replicate for Video and Aux)
CD_R
CD_R
CD_L
CD_L
RMS
(All resistors 1%)
Figure 11. Differential 2 V
Figure 12. Differential 1 V
CD input signal by 6 dB. The circuit
6.8 kΩ
6.8 kΩ
3.4 kΩ
100 Ω
100 Ω
100 Ω
6.8 kΩ
6.8 kΩ
6.8 kΩ
47 kΩ
6.8 kΩ
6.8 kΩ
47 kΩ
AGND
AGND
3.4 kΩ
1.0 µ F
1.0 µF
47 kΩ
1.0 µF
RMS
RMS
1.0 µ F
1.0 µ F
1.0 µF
6.8 kΩ
CD Input
CD Input
2.2 µF
2.2 µF
CS4299
RMS
CS4299
DS319PP6
R
L
CD_R
CD_L
CD_GND
CD_R
CD_L
CD_GND
CD in-