CS4299-JQ Cirrus Logic Inc, CS4299-JQ Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS4299-JQ
Manufacturer Part Number
CS4299-JQ
Description
Audio Codec 1ADC / 1DAC 18-Bit/20-Bit 48-Pin LQFP
Manufacturer
Cirrus Logic Inc
Type
PCMr
Datasheet
1.CS4299-JQ.pdf
(52 pages)
Specifications of CS4299-JQ
Package
48LQFP
Adc/dac Resolution
18/20 Bit
Number Of Channels
1ADC /1 DAC
Sampling Rate
48 KSPS
Number Of Adc Inputs
8
Number Of Dac Outputs
3
Number Of Dacs
1
Operating Supply Voltage
3.3|5 V
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS4299-JQ
Manufacturer:
CAYSTRL
Quantity:
5 510
Company:
Part Number:
CS4299-JQ
Manufacturer:
CRYSTAL
Quantity:
624
Company:
Part Number:
CS4299-JQEP
Manufacturer:
CAYSTRL
Quantity:
5 510
Company:
Part Number:
CS4299-JQEP
Manufacturer:
ST
Quantity:
5 510
Company:
Part Number:
CS4299-JQEP
Manufacturer:
CRYSTAL
Quantity:
210
Part Number:
CS4299-JQEP
Manufacturer:
CRYSTAL
Quantity:
20 000
Part Number:
CS4299-JQZ
Manufacturer:
CIRRUS
Quantity:
20 000
Company:
Part Number:
CS4299-JQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
DS319PP6
6.3
The AFLT1 and AFLT2 pins must have a 1000 pF
NPO capacitor to analog ground. These capacitors
provide a single-pole low-pass filter at the inputs to
the ADCs. This makes low-pass filters at each ana-
log input pin unnecessary.
The REFFLT pin must have a 1 µF and a 0.1 µF ca-
pacitor connected to analog ground with a short,
wide trace to this pin (see Figure 21 in Section 8,
Grounding and Layout, for an example). The 1 µF
capacitor must not be replaced with any value high-
er than 1 µF. No other connection should be made,
as any coupling onto this pin will degrade the ana-
log performance of the CS4299. Likewise, digital
signals should be kept away from REFFLT for sim-
ilar reasons.
The Vrefout pin is typically 2.3 V and provides a
common mode signal for single-supply external
circuits. Vrefout only supports light DC loads and
should be buffered if AC loading is needed. For
typical use the Vrefout pin should have a 1 µF and
a 0.1 µF capacitor connected to analog ground.
Miscellaneous Analog Signals
Y5V
0.1µF
DGND
+12VD
+
ELEC
10µF
Figure 19. Voltage Regulator
1
IN
MC78M05CDT
GND
2
6.4
The power supplies providing analog power should
be as clean as possible to minimize coupling into
the analog section which could degrade analog per-
formance. The analog power pins, AVdd1 and
AVdd2, supply power to all the analog circuitry on
the CS4299. The +5 V analog supply should be
generated from a linear voltage regulator (7805
type) connected to a +12 V supply. This helps iso-
late the analog circuitry from noise typically found
on +5 V digital supplies. A typical voltage regula-
tor
MC78M05CDT +5 V regulator is shown in
Figure 19. The digital power pins, DVdd1 and
DVdd2, should be connected to the same digital
supply as the controller AC-link interface. The dig-
ital interface on the CS4299 may operate at either
+3.3 V or +5 V and proper connection of these pins
will depend on the digital power supply of the con-
troller.
6.5
See Section 11 for a CS4299 reference design.
OUT
circuit
Power Supplies
Reference Design
3
Y5V
0.1µF
for
+5VA
AGND
+
ELEC
10µF
analog
power
CS4299
CS4299
using
39
39
a