SI3200-GS Silicon Laboratories Inc, SI3200-GS Datasheet - Page 28

• Manufacturer Part Number: SI3200-GS
• Description: IC LINEFEED INTRFC 100V 16SOIC
• Manufacturer: Silicon Laboratories Inc
• Series: ProSLIC®r

Specifications of SI3200-GS

• Function: Subscriber Line Interface Concept (SLIC), CODEC
• Interface: GCI, PCM, SPI
• Number Of Circuits: 2
• Voltage - Supply: 3.3V, 5V
• Current - Supply: 110µA
• Power (watts): 941mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Includes: Battery Switching, BORSCHT Functions, DTMF Generation and Decoding, FSK Tone Generation, Modem and Fax Tone Detection
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Si3220/Si3225
Functional Description
The Dual ProSLIC
solution that provides all SLIC, codec, and DTMF
detection/decoding functions needed for a complete
dual-channel analog telephone interface. Intended for
multiple-channel long-loop (up to 18 kft) applications
requiring high-density line card designs, the Dual
ProSLIC chipset provides high integration and low-
power operation for applications, such as Central Office
(CO) and digital loop carrier (DLC) enclosures. The
Dual ProSLIC chipset is also ideal for short-loop
applications requiring a space-effective solution, such
as terminal adapters, integrated access devices (IADs),
PBX/key systems, and voice-over IP systems. The
chipset meets all relevant Bellcore LSSGR, ITU, and
ETSI standards.
The Si3220/Si3225 ICs perform all battery, overvoltage,
ringing,
(BORSCHT) functions on-chip in a low-power, small-
footprint solution. DTMF decoding and generation,
phase continuous FSK (caller ID) signaling, and pulse
metering are also integrated. All high-voltage functions
are implemented using the Si3200 Linefeed Interface IC
allowing a highly-programmable integrated solution that
offers the lowest total system cost.
The internal linefeed circuitry provides programmable
on-hook voltage and off-current loop current, reverse
battery operation, loop or ground-start operation, and
on-hook transmission. Loop current and voltage are
continuously monitored using an integrated 8-bit
monitor A/D converter. The Si3220 provides on-chip
balanced 5 REN ringing with or without a programmable
dc offset eliminating the need for an external bulk ring
generator and per-channel ringing relay. Both sinusoidal
and trapezoidal ringing waveshapes are available.
Ringing parameters, such as frequency, waveshape,
cadence, and offset are available in registers to reduce
external controller requirements. The Si3225 supports
external ringing generation with ring relay driver and
external ring trip sensing to address legacy systems
that implement a centralized ringing architecture. All
ringing options are software-programmable over a wide
range of parameters to address a wide variety of
application requirements.
The Si3220/Si3225 ICs also provide a variety of line
monitoring and subscriber loop testing functions. All
versions have the ability to generate specific dc and
audio signals and continuously monitor and store all line
voltage and current parameters. This combination of
signal generation and measurement tools allows remote
line card and loop diagnostics without requiring
additional test equipment. These diagnostic functions
28
supervision,
®
chipset is a three-chip integrated
codec,
hybrid,
and
test
Rev. 1.0
are intended to comply with relevant LSSGR and ITU
requirements for line-fault detection and reporting, and
measured values are stored in registers for later use or
further calculations. The Si3220 and Si3225 also
include two per-channel relay drivers to support legacy
systems implementing centralized test equipment.
A complete audio transmit and receive path is
integrated, including DTMF generation and decoding,
tone
programmable
programmable transhybrid balance and programmable
gain
programmable providing a single hardware design to
meet international requirements. Digital voice data
transfer occurs over a standard PCM bus, and control
data is transferred using a standard 4-wire serial
peripheral interface (SPI). The Si3220 and Si3225 can
also be configured to support a 4-wire general circuit
interface (GCI). The Si3220 and Si3225 are available in
a 64-lead TQFP, and the Si3200 is available in a
thermally-enhanced 16-lead SOIC.
Dual ProSLIC Architecture
The Dual ProSLIC chipset is comprised of a low-voltage
CMOS device that uses a low-cost integrated linefeed
interface IC to control the high voltages needed for
operating the terminal equipment connected to the
telephone line. Figure 15 on page 30 presents a
simplified diagram of the linefeed control loop circuit for
controlling the TIP and RING leads. The diagram
illustrates a single-ended model for simplicity, showing
either the TIP or the RING lead.
The Dual ProSLIC chipset produces line voltages and
currents
programmable settings in the Si3220 and Si3225 as
well as direct ac and dc voltage/current sensing from
the line. The Si3200 LFIC provides a low-cost interface
for bridging the low-voltage CMOS devices to the high-
voltage TIP/RING pair. Sense resistors allow the voltage
and current to be measured on each lead or across T-R
using the low-voltage circuitry inside the Si3220 and
Si3225 eliminating expensive analog sensing circuitry
inside the high-voltage Si3200. In addition, the total
power inside the Si3200 is constantly monitored and
controlled to provide optimal reliability under all
operating conditions. The sensing circuitry is calibrated
for environmental and process variations to guarantee
accuracy with standard external resistor tolerances.
attenuation.
generation,
on
the
ac
These
TIP/RING
modem/fax
impedance
features
pair
tone
synthesis,
using
are
detection,
software-
register-
and