SI3220-BQ Silicon Laboratories Inc, SI3220-BQ Datasheet - Page 61
![IC SLIC/CODEC DUAL-CH 64TQFP](/photos/16/12/161288/tqfp-64_sml.jpg)
SI3220-BQ
Manufacturer Part Number
SI3220-BQ
Description
IC SLIC/CODEC DUAL-CH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
ProSLIC®r
Specifications of SI3220-BQ
Package / Case
*
Function
Subscriber Line Interface Concept (SLIC), CODEC
Interface
GCI, PCM, SPI
Number Of Circuits
2
Voltage - Supply
3.3V, 5V
Current - Supply
65mA
Power (watts)
941mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Includes
Battery Switching, BORSCHT Functions, DTMF Generation and Decoding, FSK Tone Generation, Modem and Fax Tone Detection
Product
Telecom
Supply Voltage (min)
3.13 V
Supply Current
22 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Number Of Channels
2
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI3220-BQ
Manufacturer:
TONTEK
Quantity:
12 000
Company:
Part Number:
SI3220-BQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Audio Characteristics
The dominant source of distortion and noise in both the
transmit and receive paths is the quantization noise
introduced by the µ -law or the A-law compression
process. Figure 5 on page 18 specifies the minimum
Signal-to-Noise-and-Distortion Ratio for either path for a
sine wave input of 200 Hz to 3400 Hz.
Both the µ -law and the A-law speech encoding allow the
audio codec to transfer and process audio signals larger
than 0 dBm0 without clipping. The maximum PCM code
is generated for a µ -law encoded sine wave of
3.17 dBm0 or an A-law encoded sine wave of
3.14 dBm0. The device overload clipping limits are
driven by the PCM encoding process. Figure 6 on page
19 shows the acceptable limits for the analog-to-analog
fundamental power transfer-function, which bounds the
behavior of the device.
The transmit path gain distortion versus frequency is
shown in Figure 7 on page 19. The same figure also
presents the minimum required attenuation for out-of-
band analog signals applied on the line. The presence
of a high-pass filter transfer-function ensures at least
30 dB of attenuation for signals below 65 Hz. The low-
pass filter transfer function attenuates signals above
3.4 kHz. It is implemented as part of the A-to-D
converter.
The receive path transfer function requirement, shown
in Figure 8 on page 20, is very similar to the transmit
path transfer function. The PCM data rate is 8 kHz so no
frequencies greater than 4 kHz are digitally encoded in
where M = {0, 1/16384, 2/16384,...32767/16384}
PCLK
Figure 39. TPGA and RPGA structure
PCM
In
PFD
TPGA or RPGA
RESET
M
X
Figure 40. PLL Frequency Synthesizer
PLL_MULT
DIV M
PCM
Out
Preliminary Rev. 0.91
the data stream. At frequencies greater than 4 kHz, the
plot in Figure 8 is interpreted as the maximum allowable
magnitude of spurious signals that are generated when
a PCM data stream representing a sine wave signal in
the range of 300 Hz to 3.4 kHz at a level of 0 dBm0 is
applied at the digital input.
The group delay distortion in either path is limited to no
more than the levels indicated in Figure 9. The
reference in Figure 9 is the smallest group delay for a
sine wave in the range of 500 Hz to 2500 Hz at 0 dBm0.
The block diagram for the voice-band signal processing
paths are shown in Figure 11 on page 22. Both the
receive and the transmit paths employ the optimal
combination of analog and digital signal processing for
maximum performance while maintaining sufficient
flexibility for users to optimize their particular application
of the device. The two-wire (TIP/RING) voice-band
interface to the device is implemented with a small
number of external components. The receive path
interface consists of a unity-gain current buffer, I
while the transmit path interface is an ac coupling
capacitor.
differentially, are shown as single-ended for simplicity.
System Clock Generation
The Dual ProSLIC devices generate the internal clock
frequencies from the PCLK input. PCLK must be
synchronous to the 8 kHz FSYNC clock and run at one
of the following rates: 256 kHz, 512 kHz, 786 kHz,
1.024 MHz,
4.096 MHz or 8.192 MHz. The ratio of the PCLK rate to
the FSYNC rate is determined by a counter clocked by
PCLK. The three-bit ratio information is transferred into
an internal register, PLL_MULT, after a device reset.
The PLL_MULT controls the internal PLL which
multiplies PCLK to generate the rate required to run the
internal filters and other circuitry.
The PLL clock synthesizer settles quickly after powerup
or update of the PLL_MULT register. However, the
settling time depends on the PCLK frequency and it is
approximately predicted by the following equation:
T
settle
= 64/F
VCO
PCLK
Signal
1.536 MHz,
÷2
paths,
Si3220/Si3225
1.544 MHz,
÷2
although
28.672 MHz
implemented
2.048 MHz,
BUF
61
,