CY8C5368AXI-106 Cypress Semiconductor Corp, CY8C5368AXI-106 Datasheet - Page 54
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CY8C5368AXI-106
Manufacturer Part Number
CY8C5368AXI-106
Description
Manufacturer
Cypress Semiconductor Corp
Datasheet
1.CY8C5368AXI-106.pdf
(106 pages)
Specifications of CY8C5368AXI-106
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY8C5368AXI-106
Manufacturer:
Cypress Semiconductor Corp
Quantity:
10 000
8.11 Sample and Hold
The main application for a sample and hold, is to hold a value
stable while an ADC is performing a conversion. Some
applications
simultaneously, such as for power calculations (V and I).
Figure 8-12. Sample and Hold Topology
( Φ 1 and Φ 2 are opposite phases of a clock)
8.11.1 Down Mixer
The S+H can be used as a mixer to down convert an input signal.
This circuit is a high bandwidth passive sample network that can
sample input signals up to 14 MHz. This sampled value is then
held using the opamp with a maximum clock rate of 4 MHz. The
output frequency is at the difference between the input frequency
and the highest integer multiple of the Local Oscillator that is less
than the input.
8.11.2 First Order Modulator - SC Mode
A first order modulator is constructed by placing the switched
capacitor block in an integrator mode and using a comparator to
provide a 1-bit feedback to the input. Depending on this bit, a
reference voltage is either subtracted or added to the input
signal. The block output is the output of the comparator and not
the integrator in the modulator case. The signal is downshifted
and buffered and then processed by a decimator to make a
delta-sigma converter or a counter to make an incremental
converter. The accuracy of the sampled data from the first-order
modulator is determined from several factors.
The main application for this modulator is for a low frequency
ADC with high accuracy. Applications include strain gauges,
thermocouples, precision voltage, and current measurement
Document Number: 001-66237 Rev. *A
V
V
n
i
ref
Φ
Φ
require
Φ
Φ
2
2
1
1
C
C
1
3
multiple
Φ
Φ
Φ
Φ
1
2
2
1
signals
C
C
2
4
to
PRELIMINARY
Φ
Φ
Φ
Φ
1
2
1
2
be
V
V
ref
ref
sampled
V
out
9. Programming, Debug Interfaces,
The Cortex-M3 has internal debugging components, tightly
integrated with the CPU, providing the following features:
PSoC devices include extensive support for programming,
testing, debugging, and tracing both hardware and firmware.
SWD supports all programming and debug features of the
device. The SWV provides trace output from the DWT and ITM.
For more information on PSoC 5 programming, refer to the
application note
PSoC
Cortex-M3 debug and trace functionality enables full device
debugging in the final system using the standard production
device. It does not require special interfaces, debugging pods,
simulators, or emulators. Only the standard programming
connections are required to fully support debug.
The PSoC Creator IDE software provides fully integrated
programming and debug support for PSoC devices. The low cost
MiniProg3 programmer and debugger is designed to provide full
programming and debug support of PSoC devices in conjunction
with the PSoC Creator IDE. PSoC interfaces are fully compatible
with industry standard third party tools.
All Cortex-M3 debug and trace modules are disabled by default
and can only be enabled in firmware. If not enabled, the only way
to reenable them is to erase the entire device, clear flash
protection, and reprogram the device with new firmware that
enables them. Disabling debug and trace features, robust flash
protection, and hiding custom analog and digital functionality
inside the PSoC device provide a level of security not possible
with multichip application solutions. Additionally, all device
interfaces can be permanently disabled (Device Security) for
applications concerned about phishing attacks due to a
maliciously reprogrammed device. Permanently disabling
interfaces is not recommended in most applications because the
designer then cannot access the device. Because all
programming, debug, and test interfaces are disabled when
Device Security is enabled, PSoCs with Device Security enabled
may not be returned for failure analysis.
SWD access
Flash Patch and Breakpoint (FPB) block for implementing
breakpoints and code patches
Data Watchpoint and Trigger (DWT) block for implementing
watchpoints, trigger resources, and system profiling
Instrumentation Trace Macrocell (ITM) for support of printf-style
debugging
PSoC
Resources
®
5.
®
5: CY8C53 Family Datasheet
AN64359 - In-System Programming for
Page 54 of 106
[+] Feedback