AD829ARZ Analog Devices Inc, AD829ARZ Datasheet - Page 16

• Manufacturer Part Number: AD829ARZ
• Description: IC VIDEO OPAMP HS LN 8-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD829ARZ

• Slew Rate: 230 V/µs
• Applications: Voltage Feedback
• Number Of Circuits: 1
• -3db Bandwidth: 120MHz
• Current - Supply: 5.3mA
• Current - Output / Channel: 32mA
• Voltage - Supply, Single/dual (±): ±4.5 V ~ 18 V
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Gain Bandwidth: 120MHz
• Supply Voltage Range: ± 4.5V To ± 18V
• No. Of Amplifiers: 1
• Output Current: 32mA
• Amplifier Output: Single Ended
• Amplifier Type: High Speed, Low Noise
• Bandwidth: 600 MHz
• Common Mode Rejection Ratio: 120
• Current, Input Bias: 3.3 μA
• Current, Input Offset: 50 nA
• Current, Output: 32 mA
• Current, Supply: 5 mA
• Impedance, Thermal: 175 °C/W
• Package Type: SOIC-8
• Power Dissipation: 0.9 W
• Resistance, Input: 13 Kilohms
• Temperature, Operating, Range: 0 to +70 °C
• Voltage, Input: -13.8 to +14.3 V (Common-Mode)
• Voltage, Noise: 1.7 nV/sqrt Hz
• Voltage, Offset: 0.2 mV
• Voltage, Output, High: +3.6 V
• Voltage, Output, Low: -3.6 V
• Voltage, Supply: ±15 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD829
HIGH GAIN VIDEO BANDWIDTH, 3-OP-AMP
INSTRUMENTATION AMPLIFIER
Figure 48 shows a 3-op-amp instrumentation amplifier circuit
that provides a gain of 100 at video bandwidths. At a circuit gain of
100, the small signal bandwidth equals 18 MHz into a FET probe.
Small signal bandwidth equals 6.6 MHz with a 50 Ω load. The
0.1% settling time is 300 ns.
+V
+V
210Ω
IN
IN
R
G
3
2
2
3
AD829
AD829
A1
A2
5
5
2kΩ
1pF
1pF
2kΩ
3pF
3pF
(G = 20)
(G = 20)
6
6
CIRCUIT GAIN =
200Ω
200Ω
Figure 48. High Gain Video Bandwidth, 3-Op-Amp In-Amp Circuit
3pF
970Ω
50Ω
DC CMR
ADJUST
4000Ω
AC CMR ADJUST
2
3
SETTLING TIME
R
G
2pF TO 8pF
AD848
A3
+ 1
1kΩ
5
5
(G = 5)
Rev. H | Page 16 of 20
6
COMM
+15V
–15V
The input amplifiers operate at a gain of 20, while the output
op amp runs at a gain of 5. In this circuit, the main bandwidth
limitation is the gain/bandwidth product of the output amplifier.
Extra care should be taken while breadboarding this circuit
because even a couple of extra picofarads of stray capacitance at the
compensation pins of A1 and A2 will degrade circuit bandwidth.
2kΩ
10µF
10µF
FREQUENCY CMRR
100Hz
1MHz
10MHz
0.1µF
0.1µF
INPUT
+V
–V
64.6dB
44.7dB
23.9dB
S
S
1µF
1µF
0.1µF
0.1µF
PIN 7
PIN 4
EACH
AMPLIFIER