AT32UC3L064 Atmel Corporation, AT32UC3L064 Datasheet - Page 466

• Manufacturer Part Number: AT32UC3L064
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L064

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.8.9.2
21.8.9.3
21.8.10
32099G–06/2011
Identifying Bus Events
Timeouts
SMBus ALERT Signal
In combined transfers, the PECEN bit should only be written to one in the last of the combined
transfers. Consider the following transfer:
S, ADR+W, COMMAND_BYTE, ACK, SR, ADR+R, DATA_BYTE, ACK, PEC_BYTE, NACK, P
This transfer is generated by writing two commands to the command registers. The first com-
mand is a write with NBYTES=1 and PECEN=0, and the second is a read with NBYTES=2 and
PECEN=1.
Writing a one to the STOP bit in CR will place a STOP condition on the bus after the current
byte. No PEC byte will be sent in this case.
The TLOWS and TLOWM fields in SMBTR configure the SMBus timeout values. If a timeout
occurs, the master will transmit a STOP condition and leave the bus. A one is also written to the
SR.TOUT bit.
A slave can get the master’s attention by pulling the TWALM line low. A one will then be written
to SR.SMBAL. This can be set up to trigger an interrupt, and software can then take the appro-
priate action, as defined in the SMBus standard.
This chapter lists the different bus events, and how they affect bits in the TWIM registers. This is
intended to help writing drivers for the TWIM.
Table 21-5.
Event
Master transmitter has sent
a data byte
Master receiver has
received a data byte
Start+Sadr sent, no ack
received from slave
Data byte sent to slave, no
ack received from slave
Arbitration lost
SMBus Alert received
SMBus timeout received
Bus Events
Effect
SR.THR is cleared.
SR.RHR is set.
SR.ANAK is set.
SR.CCOMP not set.
CMDR.VALID remains set.
STOP automatically transmitted on bus.
SR.DNAK is set.
SR.CCOMP not set.
CMDR.VALID remains set.
STOP automatically transmitted on bus.
SR.ARBLST is set.
SR.CCOMP not set.
CMDR.VALID remains set.
TWCK and TWD immediately released to a pulled-up state.
SR.SMBAL is set.
SR.SMBTOUT is set.
SR.CCOMP not set.
CMDR.VALID remains set.
STOP automatically transmitted on bus.
AT32UC3L016/32/64
466