ATmega1284P Atmel Corporation, ATmega1284P Datasheet - Page 197

• Manufacturer Part Number: ATmega1284P
• Manufacturer: Atmel Corporation

Specifications of ATmega1284P

• Flash (kbytes): 128 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.12 Examples of Baud Rate Setting
Table 19-9.
1.
8272C–AVR–06/11
Baud
Rate
(bps)
2400
4800
9600
14.4k
19.2k
28.8k
38.4k
57.6k
76.8k
115.2k
230.4k
250k
Max.
(1)
UBRR = 0, Error = 0.0%
UBRR
25
12
6
3
2
1
1
0
–
–
–
–
U2Xn = 0
Examples of UBRRn Settings for Commonly Used Oscillator Frequencies
62.5kbps
f
Error
-18.6%
osc
-7.0%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
–
–
–
–
= 1.0000MHz
For standard crystal and resonator frequencies, the most commonly used baud rates for asyn-
chronous operation can be generated by using the UBRR settings in
UBRR values which yield an actual baud rate differing less than 0.5% from the target baud rate,
are bold in the table. Higher error ratings are acceptable, but the Receiver will have less noise
resistance when the error ratings are high, especially for large serial frames (see
Operational Range” on page
UBRR
51
25
12
8
6
3
2
1
1
0
–
–
U2Xn = 1
125kbps
Error
-18.6%
-3.5%
-7.0%
0.2%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
ATmega164A/PA/324A/PA/644A/PA/1284/P
–
–
UBRR
47
23
11
7
5
3
2
1
0
–
–
1
115.2kbps
U2Xn = 0
Error[%]
189). The error values are calculated using the following equation:
Error
f
-25.0%
osc
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
–
–
= 1.8432MHz
=
⎛
⎝
BaudRate
------------------------------------------------------- - 1
UBRR
95
47
23
15
11
BaudRate
7
5
3
2
1
0
–
230.4kbps
U2Xn = 1
Closest Match
Error
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
–
–
UBRR
⎞
⎠
51
25
12
•
8
6
3
2
1
1
0
–
–
U2Xn = 0
100%
125kbps
Error
Table 19-9
f
-18.6%
-3.5%
-7.0%
osc
0.2%
0.2%
0.2%
8.5%
8.5%
8.5%
8.5%
–
–
= 2.0000MHz
UBRR
103
to
51
25
16
12
”Asynchronous
8
6
3
2
1
–
0
U2Xn = 1
250kbps
Table
Error
-3.5%
-7.0%
0.2%
0.2%
0.2%
2.1%
0.2%
8.5%
8.5%
8.5%
0.0%
19-12.
–
197