ATmega164P Atmel Corporation, ATmega164P Datasheet - Page 240

• Manufacturer Part Number: ATmega164P
• Manufacturer: Atmel Corporation

Specifications of ATmega164P

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20. ADC - Analog-to-digital Converter
20.1
20.2
8011O–AVR–07/10
Features
Overview
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Note:
The ATmega164P/324P/644P features a 10-bit successive approximation ADC. The ADC is
connected to an 8-channel Analog Multiplexer which allows 8 single-ended voltage inputs con-
structed from the pins of Port A. The single-ended voltage inputs refer to 0V (GND).
The device also supports 16 differential voltage input combinations. Two of the differential inputs
(ADC1, ADC0 and ADC3, ADC2) are equipped with a programmable gain stage. This provides
amplification steps of 0 dB (1x), 20 dB (10x), or 46 dB (200x) on the differential input voltage
before the A/D conversion. Seven differential analog input channels share a common negative
terminal (ADC1), while any other ADC input can be selected as the positive input terminal. If 1x
or 10x gain is used, 8-bit resolution can be expected. If 200x gain is used, 6-bit resolution can be
expected. Note that internal references of 1.1V should not be used on 10x and 200x gain.
The ADC contains a Sample and Hold circuit which ensures that the input voltage to the ADC is
held at a constant level during conversion. A block diagram of the ADC is shown in
on page
The ADC has a separate analog supply voltage pin, AVCC. AVCC must not differ more than
±0.3 V from V
pin.
Internal reference voltages of nominally 1.1V, 2.56V or AVCC are provided On-chip. The voltage
reference may be externally decoupled at the AREF pin by a capacitor for better noise perfor-
mance. If V
ended channels.
10-bit Resolution
0.5 LSB Integral Non-linearity
±2 LSB Absolute Accuracy
13 µs - 260 µs Conversion Time
Up to 15 kSPS at Maximum Resolution
8 Multiplexed Single Ended Input Channels
Differential mode with selectable gain at 1x, 10x or 200x
Optional Left adjustment for ADC Result Readout
0V - V
2.7V - V
Selectable 2.56V or 1.1V ADC Reference Voltage
Free Running or Single Conversion Mode
ADC Start Conversion by Auto Triggering on Interrupt Sources
Interrupt on ADC Conversion Complete
Sleep Mode Noise Canceler
CC
1. The differential input channels are not tested for devices in PDIP Package. This feature is only
241.
CC
ADC Input Voltage Range
guaranteed to work for devices in TQFP and VQFN/QFN/MLF Packages.
Differential ADC Voltage Range
CC
CC
is below 2.1V, internal voltage reference of 1.1V should not be used on single
. See the paragraph
”ADC Noise Canceler” on page 248
ATmega164P/324P/644P
on how to connect this
Figure 20-1
240