ATmega164P Atmel Corporation, ATmega164P Datasheet - Page 258

• Manufacturer Part Number: ATmega164P
• Manufacturer: Atmel Corporation

Specifications of ATmega164P

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20.9.3
ADLAR = 0
ADLAR = 1
20.9.4
8011O–AVR–07/10
ADCL and ADCH – The ADC Data Register
ADCSRB – ADC Control and Status Register B
Table 20-5.
When an ADC conversion is complete, the result is found in these two registers. If differential
channels are used, the result is presented in two’s complement form.
When ADCL is read, the ADC Data Register is not updated until ADCH is read. Consequently, if
the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read
ADCH. Otherwise, ADCL must be read first, then ADCH.
The ADLAR bit in ADMUX, and the MUXn bits in ADMUX affect the way the result is read from
the registers. If ADLAR is set, the result is left adjusted. If ADLAR is cleared (default), the result
is right adjusted.
• ADC9:0: ADC Conversion Result
These bits represent the result from the conversion, as detailed in
page
Bit
(0x79)
(0x78)
Read/Write
Initial Value
Bit
(0x79)
(0x78)
Read/Write
Initial Value
Bit
(0x7B)
Read/Write
Initial Value
253.
ADPS2
1
1
1
1
ADC Prescaler Selections (Continued)
ADC7
ADC9
ADC1
15
15
R
R
R
R
–
7
0
0
7
0
0
R
7
–
0
ACME
ADC6
ADC8
ADC0
R/W
14
14
R
R
R
R
ADPS1
–
6
0
0
6
0
0
6
0
0
0
1
1
ADC5
ADC7
13
13
R
R
R
R
R
–
5
0
0
–
5
0
0
5
–
0
ADC4
ADC6
12
12
R
R
R
R
–
4
0
0
–
4
0
0
R
4
–
0
ADPS0
0
1
0
1
ATmega164P/324P/644P
ADC3
ADC5
11
11
R
R
R
R
–
3
0
0
–
3
0
0
R
3
–
0
ADTS2
ADC2
ADC4
R/W
10
10
R
R
R
R
–
2
0
0
–
2
0
0
2
0
”ADC Conversion Result” on
ADTS1
ADC9
ADC1
ADC3
Division Factor
R/W
R
R
R
R
9
1
0
0
9
–
1
0
0
1
0
128
16
32
64
ADTS0
ADC8
ADC0
ADC2
R/W
R
R
R
R
8
0
0
0
8
–
0
0
0
0
0
ADCSRB
ADCH
ADCH
ADCL
ADCL
258