ATmega169P Atmel Corporation, ATmega169P Datasheet - Page 32

• Manufacturer Part Number: ATmega169P
• Manufacturer: Atmel Corporation

Specifications of ATmega169P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.3
8.4
8018P–AVR–08/10
Default Clock Source
Calibrated Internal RC Oscillator
The device is shipped with CKSEL = “0010”, SUT = “10”, and CKDIV8 programmed. The default
clock source setting is the Internal RC Oscillator with longest start-up time and an initial system
clock prescaling of 8. This default setting ensures that all users can make their desired clock
source setting using an In-System or Parallel programmer.
B default, the Internal RC Oscillator provides an approximate 8 MHz clock. Though voltage and
temperature dependent, this clock can be very accurately calibrated by the user. See
on page 332
with the CKDIV8 Fuse programmed. See
This clock may be selected as the system clock by programming the CKSEL Fuses as shown in
Table
the pre-programmed calibration value into the OSCCAL Register and thereby automatically cali-
brates the RC Oscillator. The accuracy of this calibration is shown as Factory calibration in
28-2 on page
By changing the OSCCAL register from SW, see
page
The accuracy of this calibration is shown as User calibration in
When this Oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section
Table 8-3.
Notes:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 8-4.
Note:
Power Conditions
BOD enabled
Fast rising power
Slowly rising power
38, it is possible to get a higher calibration accuracy than by using the factory calibration.
8-3. If selected, it will operate with no external components. During reset, hardware loads
8-4.
1. The device is shipped with this option selected.
2. The frequency ranges are preliminary values. Actual values are TBD.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
1. The device is shipped with this option selected
Fuse can be programmed in order to divide the internal frequency by 8.
and
332.
Internal Calibrated RC Oscillator Operating Modes
Start-up times for the internal calibrated RC Oscillator clock selection
Frequency Range
”Internal Oscillator Speed” on page 365
7.3 - 8.1
Start-up Time from Power-
”Calibration Byte” on page
down and Power-save
(2)
(MHz)
Reserved
6 CK
6 CK
6 CK
”System Clock Prescaler” on page 37
”OSCCAL – Oscillator Calibration Register” on
.
299.
for more details. The device is shipped
Additional Delay from
Reset (V
Table 28-2 on page
14CK + 65 ms
14CK + 4.1 ms
(1)(3)
14CK
ATmega169P
CC
CKSEL3:0
= 5.0V)
0010
(1)
CC
for more details.
), the CKDIV8
332.
Table 28-2
SUT1:0
00
01
10
11
Table
32