ATmega3290 Atmel Corporation, ATmega3290 Datasheet - Page 294

• Manufacturer Part Number: ATmega3290
• Manufacturer: Atmel Corporation

Specifications of ATmega3290

• Flash (kbytes): 32 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.2
294
Fuse Bits
ATmega329/3290/649/6490
Table 27-2.
Notes:
The ATmega329/3290/649/6490 has three Fuse bytes.
the functionality of all the fuses and how they are mapped into the Fuse bytes. Note that the
fuses are read as logical zero, “0”, if they are programmed.
Table 27-3.
Notes:
Extended Fuse Byte
–
–
–
–
–
BODLEVEL1
BODLEVEL0
RSTDISBL
BLB1 Mode
1
2
3
4
Memory Lock Bits
1. Program the Fuse bits and Boot Lock bits before programming the LB1 and LB2.
2. “1” means unprogrammed, “0” means programmed
1. See
2. Port G, PG5 is input only. Pull-up is always on.
(2)
79.
(1)
(1)
Lock Bit Protection Modes
Extended Fuse Byte
BLB12
Table 28-5 on page 330
1
1
0
0
Bit No
7
6
5
4
5
2
1
0
BLB11
1
0
0
1
Description
–
–
–
–
–
Brown-out Detector trigger level
Brown-out Detector trigger level
External Reset Disable
Protection Type
No restrictions for SPM or LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section,
and LPM executing from the Application section is not
allowed to read from the Boot Loader section. If Interrupt
Vectors are placed in the Application section, interrupts
are disabled while executing from the Boot Loader section.
LPM executing from the Application section is not allowed
to read from the Boot Loader section. If Interrupt Vectors
are placed in the Application section, interrupts are
disabled while executing from the Boot Loader section.
for BODLEVEL Fuse decoding.
(1)(2)
(Continued)
See “Alternate Functions of Port G” on page
Table 27-3
Default Value
1
1
1
1
1
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
-
Table 27-5
describe briefly
2552K–AVR–04/11