ATmega3290 Atmel Corporation, ATmega3290 Datasheet - Page 52

• Manufacturer Part Number: ATmega3290
• Manufacturer: Atmel Corporation

Specifications of ATmega3290

• Flash (kbytes): 32 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

11.1.1
11.2
11.2.1
52
Register Description
ATmega329/3290/649/6490
Moving Interrupts Between Application and Boot Space
MCUCR – MCU Control Register
When the BOOTRST Fuse is programmed, the Boot section size set to 4K bytes and the IVSEL
bit in the MCUCR Register is set before any interrupts are enabled, the most typical and general
program setup for the Reset and Interrupt Vector Addresses is:
The MCU Control Register controls the placement of the Interrupt Vector table.
• Bit 1 – IVSEL: Interrupt Vector Select
When the IVSEL bit is cleared (zero), the Interrupt Vectors are placed at the start of the Flash
memory. When this bit is set (one), the Interrupt Vectors are moved to the beginning of the Boot
Loader section of the Flash. The actual address of the start of the Boot Flash Section is deter-
mined by the BOOTSZ Fuses. Refer to the section
Bit
0x35 (0x55)
Read/Write
Initial Value
0x0004
...
0x002C
;
.org 0x3800/0x7800
0x3800/0x7801RESET:ldir16,high(RAMEND); Main program start
0x3801/0x7801
0x3802/0x7802
0x3803/0x7803
0x3804/0x7804
0x3805/0x7805
Address Labels Code
;
.org 0x3800/0x7800
0x3800/0x7800
0x3802/0x7802
0x3804/0x7804
...
0x382C/0x782C
;
0x382E/0x782ERESET:ldir16,high(RAMEND); Main program start
0x382F/0x782F
0x3830/0x7830
0x3831/0x7831
0x3832/0x7832
0x3833/0x7833
JTD
R/W
7
0
jmp
...
jmp
out
ldi
out
sei
<instr>
jmp
jmp
jmp
...
jmp
out
ldi
out
sei
<instr>
R
6
–
0
PCINT0
...
SPM_RDY
SPH,r16
r16,low(RAMEND)
SPL,r16
RESET
EXT_INT0
PCINT0
...
SPM_RDY
SPH,r16
r16,low(RAMEND)
SPL,r16
R
5
–
0
xxx
xxx
PUD
R/W
4
0
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Set Stack Pointer to top of RAM
; PCINT0 Handler
;
; Store Program Memory Ready Handler
; Enable interrupts
Comments
; Reset handler
; IRQ0 Handler
; PCINT0 Handler
;
; Enable interrupts
R
3
–
0
“Boot Loader Support – Read-While-Write
R
2
–
0
IVSEL
R/W
1
0
IVCE
R/W
0
0
MCUCR
2552K–AVR–04/11