ATmega6490 Atmel Corporation, ATmega6490 Datasheet - Page 97
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega6490
Manufacturer Part Number
ATmega6490
Description
Manufacturer
Atmel Corporation
Specifications of ATmega6490
Flash (kbytes)
64 Kbytes
Pin Count
100
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
69
Ext Interrupts
32
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
160
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega6490-16AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega6490-16AU
Manufacturer:
Atmel
Quantity:
135
Company:
Part Number:
ATmega6490-16AUR
Manufacturer:
Atmel
Quantity:
1 500
Company:
Part Number:
ATmega6490A-AU
Manufacturer:
Atmel
Quantity:
1 250
Company:
Part Number:
ATmega6490A-AUR
Manufacturer:
Maxim
Quantity:
43
Company:
Part Number:
ATmega6490P-AU
Manufacturer:
Atmel
Quantity:
779
14.7
14.7.1
14.7.2
2552K–AVR–04/11
Modes of Operation
Normal Mode
Clear Timer on Compare Match (CTC) Mode
The mode of operation, i.e., the behavior of the Timer/Counter and the Output Compare pins, is
defined by the combination of the Waveform Generation mode (WGM01:0) and Compare Output
mode (COM0A1:0) bits. The Compare Output mode bits do not affect the counting sequence,
while the Waveform Generation mode bits do. The COM0A1:0 bits control whether the PWM
output generated should be inverted or not (inverted or non-inverted PWM). For non-PWM
modes the COM0A1:0 bits control whether the output should be set, cleared, or toggled at a
compare match
For detailed timing information refer to
in
The simplest mode of operation is the Normal mode (WGM01:0 = 0). In this mode the counting
direction is always up (incrementing), and no counter clear is performed. The counter simply
overruns when it passes its maximum 8-bit value (TOP = 0xFF) and then restarts from the bot-
tom (0x00). In normal operation the Timer/Counter Overflow Flag (TOV0) will be set in the same
timer clock cycle as the TCNT0 becomes zero. The TOV0 Flag in this case behaves like a ninth
bit, except that it is only set, not cleared. However, combined with the timer overflow interrupt
that automatically clears the TOV0 Flag, the timer resolution can be increased by software.
There are no special cases to consider in the Normal mode, a new counter value can be written
anytime.
The Output Compare unit can be used to generate interrupts at some given time. Using the Out-
put Compare to generate waveforms in Normal mode is not recommended, since this will
occupy too much of the CPU time.
In Clear Timer on Compare or CTC mode (WGM01:0 = 2), the OCR0A Register is used to
manipulate the counter resolution. In CTC mode the counter is cleared to zero when the counter
value (TCNT0) matches the OCR0A. The OCR0A defines the top value for the counter, hence
also its resolution. This mode allows greater control of the compare match output frequency. It
also simplifies the operation of counting external events.
The timing diagram for the CTC mode is shown in
increases until a compare match occurs between TCNT0 and OCR0A, and then counter
(TCNT0) is cleared.
“Timer/Counter Timing Diagrams” on page
(See “Compare Match Output Unit” on page
Figure
ATmega329/3290/649/6490
101.
14-8,
Figure
Figure
14-9,
95.).
14-5. The counter value (TCNT0)
Figure 14-10
and
Figure 14-11
97